Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD (for Column Shift Type)

INSTRUMENT PANEL SAFETY PAD (for Column Shift Type) > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL NO. 1 INSTRUMENT PANEL CLIP
  1. Attach the 2 claws to install the 2 No. 1 instrument panel clips.



2. INSTALL NO. 3 INSTRUMENT PANEL STAY
  1. Attach the 3 claws to install the 3 No. 3 instrument panel stays.



3. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Set the instrument panel sub-assembly and attach the 5 claws.

  1. Install the 2 nuts <C> and 3 bolts <B>.



  1. Install the 2 bolts <G>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



    B356779E01


    Text in Illustration 
    *1
    Bolt <G>
    *2
    Bolt <B>
    *2
    Nut <C>
    -
    -



  1. Connect each connector and attach each wire harness clamp.


    B355370E01


    Text in Illustration 
    *A
    w/ Automatic Light Control System
    *B
    w/ Front Center Speaker



4. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH
  1. Connect the connector.

  1. Temporarily install the front No. 2 speaker assembly LH by aligning the positioning pins of the front No. 2 speaker assembly LH with the instrument panel.

  1. Install the front No. 2 speaker assembly LH with the 2 bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful so that the wires do not get caught between the parts.



5. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B355369
  1. Attach the 3 clips and 2 claws to install the instrument panel speaker panel sub-assembly.



6. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH
  1. Connect the connector.

  1. Temporarily install the front No. 2 speaker assembly RH by aligning the positioning pins of the front No. 2 speaker assembly RH with the instrument panel.

  1. Install the front No. 2 speaker assembly RH with the 2 bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. When installing the speaker to the instrument panel, be careful so that the wires do not get caught between the parts.



7. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedure described for the instrument panel speaker panel sub-assembly.



8. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the clip to install the front pillar garnish LH.

  1. Install the bolt.



    B355362
  1. Attach the claw to close the cover.



9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. for Double Cab:

  1. for CrewMax:

  1. for Regular Cab:



10. INSTALL FRONT PILLAR GARNISH RH
  1. Attach the clip to install the front pillar garnish RH.

  1. Install the front assist grip sub-assembly to the front pillar garnish RH with the 2 bolts.



    B355365
  1. Attach the 2 claws to close the 2 assist grip covers.



11. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. for 4WD:
    Connect the connector.



    B355360
  1. Attach the 18 clips and wire harness clamp to install the center instrument cluster finish panel sub-assembly.



13. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
  1. Connect each connector.

  1. Insert the radio and display receiver assembly with bracket and attach the 2 guides and 3 clips on its backside.

    NOTICE:
    When inserting the radio receiver, do not press its knobs.

  1. Install the radio and display receiver assembly with bracket with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



14. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY
  1. Connect each connector.



  1. Attach the 8 clips, 2 claws and guide to install the lower center instrument panel finish panel together with the air conditioning control assembly.


    E281400E01


    Text in Illustration 
    *A
    for Automatic Air Conditioning System
    *B
    for Manual Air Conditioning System
    *1
    Protective Tape
    *2
    Air Conditioning Control Assembly
    *3
    Lower Center Instrument Panel Finish Panel
    -
    -



15. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B355354
  1. Attach the 3 claws and 4 clips to install the No. 2 instrument cluster finish panel garnish.



16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B355352
  1. Attach the 4 claws to install the lower instrument panel finish panel sub-assembly RH.

  1. Install the 4 screws <F> and bolt <A>.



17. INSTALL INSTRUMENT SIDE PANEL RH


    B355356
  1. Attach the 4 guides and 3 claws to install the instrument side panel RH.



18. INSTALL NO. 4 INSTRUMENT REGISTER SUB-ASSEMBLY


B355349
  1. Attach the 10 clips to install the No. 4 instrument register sub-assembly.



19. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B226008
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the 3 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



20. INSTALL LOWER INSTRUMENT PANEL
  1. Attach the 3 claws to install the lower instrument panel.

  1. Install the bolt <A> and screw <D>.



21. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Attach the 2 guides, 4 claws and clip to install the No. 2 instrument panel under cover sub-assembly.



22. INSTALL COMBINATION METER ASSEMBLY
  1. Pass the combination meter assembly between the steering wheel assembly and instrument panel.



  1. Connect the connector and attach the wire harness clamp.


    E281860E01


    Text in Illustration 
    *A
    for Column Shift Type
    *2
    for Floor Shift Type

  1. Install the combination meter assembly with the 4 screws.



23. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
  1. Attach the 6 clips to install the instrument cluster finish panel assembly.

  1. Install the 2 clips.



24. INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT


B355346
  1. Attach the 3 clips and claw to install the instrument cluster finish panel ornament.



25. INSTALL NO. 2 SWITCH HOLE BASE
  1. Connect each connector.



    B355344
  1. Attach the 4 clips to install the No. 2 switch hole base.



26. INSTALL UPPER STEERING COLUMN COVER


    C290068
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



27. INSTALL LOWER STEERING COLUMN COVER
  1. Attach the 2 claws to install the lower steering column cover.

  1. While turning the steering wheel assembly to the right and left, install the 2 screws.



28. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B355342
  1. Attach the 3 clips and 3 claws to install the No. 1 instrument cluster finish panel garnish.



29. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



30. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


  1. Connect the hood lock control cable to the hood lock control lever, rotate the hood lock control cable, and then slide and push the hood lock control cable into place.


    B355340

  1. Attach the 3 hooks to connect the hood lock control lever to the lower instrument panel finish panel sub-assembly LH.

  1. Connect each connector.



    B355338
  1. Attach the 9 clips and 2 claws to install the lower instrument panel finish panel sub-assembly LH.

  1. Install the 2 bolts <A>.



31. INSTALL COWL SIDE TRIM BOARD LH
  1. Attach the 2 clips to install the cowl side trim board LH.

  1. Install the nut.



32. INSTALL FRONT DOOR SCUFF PLATE LH
  1. for Double Cab:

  1. for CrewMax:

  1. for Regular Cab:



33. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



34. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



35. INSTALL LOWER CENTER INSTRUMENT COVER
  1. Attach the 2 guides and 2 clips to install the lower center instrument cover.

  1. Install the 2 clips.



36. INSTALL INSTRUMENT SIDE PANEL LH


    B355334
  1. Attach the 4 guides and 3 claws to install the instrument side panel LH.



37. INSTALL NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY


    B355332
  1. Attach the 4 clips to install the No. 1 instrument panel register sub-assembly.



38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



39. CHECK SRS WARNING LIGHT
(Click here)