Home › BODY ELECTRICAL › LIGHTING › HEADLIGHT DIMMER SWITCH

HEADLIGHT DIMMER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY


E139363E46
  1. Inspect the light control switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      20 (H) - 12 (EL)
      Light control switch off
      10 kΩ or higher
      18 (T) - 12 (EL)
      19 (A) - 12 (EL)
      18 (T) - 12 (EL)
      Light control switch tail
      Below 1 Ω
      18 (T) - 12 (EL)
      Light control switch head
      Below 1 Ω
      20 (H) - 12 (EL)
      19 (A) - 12 (EL)
      Light control switch auto
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)



    E139363E43
  1. Inspect the headlight dimmer switch.

    1. Measure the resistance according to the value(s) in the table below.

      HINT:
      Perform the flash, high beam and low beam inspections with the light control switch on head.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      11 (HU) - 12 (EL)
      Headlight dimmer switch flash
      Below 1 Ω
      17 (HF) - 12 (EL)
      11 (HU) - 12 (EL)
      Headlight dimmer switch hi beam
      Below 1 Ω
      16 (HL) - 12 (EL)
      Headlight dimmer switch low beam
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)



    E139363E44
  1. Inspect the turn signal switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      13 (TR) - 12 (EL)
      Turn signal switch right turn
      Below 1 Ω
      13 (TR) - 12 (EL)
      Turn signal switch right lane change
      Below 1 Ω
      13 (TR) - 12 (EL)
      Turn signal switch neutral
      10 kΩ or higher
      15 (TL) - 12 (EL)
      15 (TL) - 12 (EL)
      Turn signal switch left lane change
      Below 1 Ω
      15 (TL) - 12 (E)
      Turn signal switch left turn
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)



    E139363E45
  1. Inspect the front fog light switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (LFG) - 4 (BFG)
      Front fog light switch off
      10 kΩ or higher
      3 (LFG) - 4 (BFG)
      Front fog light switch on
      Below 1 Ω

      If the result is not as specified, replace the headlight dimmer switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)