Home › BODY › INSTRUMENT PANEL › INSTRUMENT PANEL SAFETY PAD (for Floor Shift Type)

INSTRUMENT PANEL SAFETY PAD (for Floor Shift Type) > REMOVAL

for Preparation Click here



1. TABLE OF BOLT, SCREW AND NUT


HINT:
All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.



B356636E01



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISABLE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)
  1. Disable the Autoaway/Return function by changing the customize parameter (Click here).

    NOTICE:
    Record the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.

  1. Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column.

  1. Turn the ignition switch off.



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. REMOVE NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY


B355331E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover B, detach the 4 clips and remove the No. 1 instrument panel register sub-assembly.



6. REMOVE INSTRUMENT SIDE PANEL LH


    B355333
  1. Using a moulding remover B, detach the 3 claws, 4 guides and remove the instrument side panel LH.



7. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B355384
  1. Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.



8. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY
  1. Move the shift lever to N.



    B355386E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover B, detach the 6 clips and remove the upper rear console panel sub-assembly.



9. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B355388
  1. Detach the 12 clips and remove the upper console panel sub-assembly.



10. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY


    B355389
  1. Using a moulding remover B, detach the 7 clips and remove the rear console end panel sub-assembly.

  1. w/ Power Outlet Socket:
    Detach the 2 wire harness clamps and disconnect the connector.



11. REMOVE CONSOLE BOX CARPET


B355391
  1. Remove the console box carpet.



12. REMOVE REAR CONSOLE BOX ASSEMBLY


    B355392
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws <E> and 4 bolts <B> and rear console box assembly.



13. REMOVE FRONT CONSOLE BOX


    B355393
  1. Remove the 2 clips and detach the connector.

  1. Remove the 5 screws <E> and front console box.



14. REMOVE FRONT DOOR SCUFF PLATE LH


B165841
  1. Detach the 6 claws and 3 clips, and remove the front door scuff plate LH.



15. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the nut.

  1. Detach the 2 clips and remove the cowl side trim board LH.



16. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.



17. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.



18. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH
  1. Operate the tilt lever to fully extend and raise the steering column.



    B355337E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the 2 bolts <A>.

  1. Detach the 9 clips, 2 claws and remove the lower instrument panel finish panel sub-assembly LH.

  1. Disconnect each connector.



    B355336
  1. Detach the 3 hooks and disconnect the hood lock control lever from the lower instrument panel finish panel sub-assembly LH.



  1. Pull and slide the hood lock control cable, rotate the hood lock control cable, and then disconnect the hood lock control cable from the hood lock control lever.


    B355339



19. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225997
  1. Remove the 4 bolts and remove the instrument panel airbag.

  1. Detach the 2 claws and disconnect the DLC3.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



20. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


B355341
  1. Using a moulding remover B, detach the 3 claws, 3 clips and remove the No. 1 instrument cluster finish panel garnish.



21. REMOVE NO. 2 SWITCH HOLE BASE


    B355394E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Detach the 4 clips and remove the No. 2 switch hole base.

  1. Disconnect each connector.



22. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT


    B355396E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Detach the 3 clips, claw and remove the instrument cluster finish panel ornament.



23. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B355398
  1. Remove the 2 clips.

  1. Detach the 6 clips and remove the instrument cluster finish panel assembly.



24. REMOVE COMBINATION METER ASSEMBLY


  1. for Floor Shift Type:
    Apply protective tape as shown in the illustration.


    E281856E01


    Text in Illustration 
    *A
    for Column Shift Type
    *B
    for Floor Shift Type
    *1
    Protective Tape
    -
    -

  1. Remove the 4 screws.



  1. Move the combination meter assembly as shown in the illustration and disconnect the connector and detach the wire harness clamp.


    E281857E01


    Text in Illustration 
    *A
    for Column Shift Type
    *B
    for Floor Shift Type

  1. Pass the combination meter assembly between the steering wheel assembly and instrument panel.



25. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B226758
  1. Detach the clip, 4 claws and 2 guides and remove the No. 2 instrument panel under cover sub-assembly.



26. REMOVE LOWER INSTRUMENT PANEL


    B355350
  1. Remove the screw <D> and bolt <A>.

  1. Detach the 3 claws and remove the lower instrument panel.



27. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B226007
  1. Remove the 3 bolts and remove the instrument panel airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



28. REMOVE NO. 4 INSTRUMENT REGISTER SUB-ASSEMBLY


    B355348E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover B, detach the 10 clips and remove the No. 4 instrument register sub-assembly.



29. REMOVE INSTRUMENT SIDE PANEL RH


    B355355
  1. Using a moulding remover B, detach the 3 claws, 4 guides and remove the instrument side panel RH.



30. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH


    B355351E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Remove the bolt <A> and 4 screws <F>.

  1. Detach the 4 claws and remove the lower instrument panel finish panel sub-assembly RH.



31. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B355353E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover B, detach the 4 clips, 3 claws and remove the No. 2 instrument cluster finish panel garnish.



32. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY


  1. Apply protective tape as shown in the illustration.


    E281399E01


    Text in Illustration 
    *A
    for Automatic Air Conditioning System
    *B
    for Manual Air Conditioning System
    *1
    Protective Tape
    *2
    Air Conditioning Control Assembly
    *3
    Lower Center Instrument Panel Finish Panel
    -
    -

  1. Using moulding remover B, detach the 8 clips, 2 claws and guide and remove the lower center instrument panel finish panel together with the air conditioning control assembly.

  1. Disconnect each connector.



33. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET


    B353907
  1. Remove the 4 bolts.



    B353908
  1. Pull the radio and display receiver assembly with bracket to detach the 3 clips and 2 guides on the backside of the radio and display receiver assembly with bracket.

  1. Disconnect each connector and remove the radio and display receiver assembly with bracket.



34. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B355359E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Detach the wire harness clamp and 18 clips and remove the center instrument cluster finish panel sub-assembly.

  1. for 4WD:
    Disconnect the connector.



35. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
  1. Remove the front door opening trim weatherstrip LH.



36. REMOVE FRONT PILLAR GARNISH LH


    B355361E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the claw and open the cover.

    HINT:
    Tape the screwdriver tip before use.



    B355363
  1. Remove the bolt.

  1. Detach the clip and remove the front pillar garnish LH.



  1. Protect the curtain shield airbag assembly.



      B165709E07
    1. Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.

      Text in Illustration 
      *1
      Adhesive Tape
      *2
      Protective Cover
      *3
      Curtain Shield Airbag Assembly



37. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.



38. REMOVE FRONT PILLAR GARNISH RH


    B355364E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 2 claws and open the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.



    B355366
  1. Remove the 2 bolts and front assist grip sub-assembly from the front pillar garnish RH.



    B355367
  1. Detach the clip and remove the front pillar garnish RH.

  1. Protect the curtain shield airbag assembly.

    1. Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape.

      NOTICE:
      Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.



39. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B355368E01
  1. Apply protective tape as shown in the illustration.
    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover B, detach the 2 claws, 3 clips and remove the instrument panel speaker panel sub-assembly.



40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY LH


  1. Remove the 2 bolts.


    B355104E01


    Text in Illustration 
    *A
    for Standard
    *B
    for 7 Speakers

  1. Disconnect the connector and remove the front No. 2 speaker assembly LH.

    NOTICE:
    Do not touch the cone part of the speaker.



41. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:
Use the same procedure described for the instrument panel speaker panel sub-assembly.



42. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY RH



B355105E01


Text in Illustration 
*A
for Standard
*B
for 7 Speakers
  1. Remove the 2 bolts.

  1. Disconnect the connector and remove the front No. 2 speaker assembly RH.

    NOTICE:
    Do not touch the cone part of the speaker.



43. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
  1. for Manual Tilt Steering Column:
    Operate the tilt lever to fully extend and lower the steering column.

  1. Disconnect each connector and each wire harness clamp.



  1. for Automatic Air Conditioning System:
    Detach the 2 claws and disconnect the cooler thermistor.


    B355399E01


    Text in Illustration 
    *A
    w/ Automatic Light Control System
    *B
    w/ Front Center Speaker
    *C
    for Automatic Air Conditioning System
    -
    -



  1. Apply protective tape as shown in the illustration.


    B355400E01


    Text in Illustration 
    *1
    Protective Tape
    *2
    Bolt <G>
    *3
    Bolt <B>
    *4
    Nut <C>

  1. Remove the 2 bolts <G>.

  1. Remove the 3 bolts <B> and 2 nuts <C>.

  1. Detach the 5 claws and remove the instrument panel sub-assembly.



44. REMOVE NO. 3 INSTRUMENT PANEL STAY


  1. Detach the 3 claws and remove the 3 No. 3 instrument panel stays.


    B355373



45. REMOVE NO. 1 INSTRUMENT PANEL CLIP


  1. Detach the 2 claws and remove the 2 No. 1 instrument panel clips.


    B355372