Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.

  2. The table below shows the effects on each system when communication is impossible. For further details, refer to each system.

    Function
    Behavior during CAN Failure
    1. Control Master
    2. System Related
    Vehicle Behavior
    Indicator and Buzzer
    Diagnostic Trouble Code
    Compressor Control/Lock Judgment
    (Determines whether compressor is locked.)
    1. Air conditioning amplifier assembly
    2. ECM
    1. When there is not a periodic malfunction:
      1. Performs control with engine speed as 0 rpm.
      2. Cannot determine whether compressor is locked.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    B1499
    Forced Air Recirculation Control
    (Performs forced air recirculation when coolant temperature is high.)
    1. Air conditioning amplifier assembly
    2. ECM
    1. When there is not a periodic malfunction, cannot perform forced air recirculation when coolant temperature is high.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    Coolant Temperature Correction Control/Warm-up Control
    (Performs A/C correction based on the engine coolant temperature.)
    1. Air conditioning amplifier assembly
    2. ECM
    1. When there is not a periodic malfunction:
      1. Performs control with engine coolant temperature as 80°C (176°F).
      2. Cannot perform warm-up control.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    Vent Control/Automatic FOOT/DEF Control
    (Performs vent control according to automatic FOOT/DEF.)
    1. Air conditioning amplifier assembly
    2. ECM, Combination meter assembly
    1. When there is not a periodic malfunction:
      1. Performs control with engine coolant temperature as 80°C (176 °F)(when communication is lost with the ECM).
      2. Performs control with vehicle speed as 0 km/h (0 mph) (when communication is lost with the combination meter assembly).
      3. Cannot perform automatic FOOT/DEF control
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    Engine Model Information Judgment
    (Uses the engine model information to determine the engine type.)
    1. Air conditioning amplifier assembly
    2. ECM
    1. When there is not a periodic malfunction, the default settings are used.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    Ambient Temperature Display
    (Sends the ambient temperature data to the combination meter and displays it on the multi-information display.)
    1. Air conditioning amplifier assembly
    2. Combination meter assembly
    1. When there is not a periodic malfunction, the ambient temperature cannot be displayed.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    Defogger Control
    (Performs defogger control.)
    1. Air conditioning amplifier assembly
    2. Combination meter assembly
    1. When there is not a periodic malfunction, cannot perform defogger control.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    A/C Control/Correction Using Vehicle Speed
    (A/C control is performed according to the vehicle speed.)
    1. Air conditioning amplifier assembly
    2. Combination meter assembly
    1. When there is not a periodic malfunction:
      1. Performs control with vehicle speed as 0 km/h (0 mph).
      2. Cannot perform correction using vehicle speed.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    Temperature Unit of Measurement
    (Determines the unit of measurement for the temperature.)
    1. Air conditioning amplifier assembly
    2. Combination meter assembly
    1. When there is not a periodic malfunction, the unit of measurement is set to °F.
    2. When there is a periodic malfunction, the previous value is maintained.
    Nothing
    Nothing
    Memory Seat
    (Memorizes and recalls the seat position.)
    1. Front power seat control ECU and switch LH
    2. ECM, Main body ECU (driver side junction block assembly), Outer mirror control ECU assembly, Multiplex tilt and telescopic ECU
    1. If communication is lost with the ECM:
      1. The position is not recalled when ignition switch is turned to ON.
      2. The position cannot be memorized or recalled.
    2. If communication is lost with the main body ECU or outer mirror control ECU assembly: The position cannot be memorized or recalled.
    3. If communication is lost with the multiplex tilt and telescopic ECU: The tilt position cannot be memorized or recalled.
    Nothing
    Nothing
    2WD-4WD LOW Switching Limitation and 4WD-4WD LOW Switching Limitation
    (When there is a wheel speed signal malfunction, 2WD-4WD LOW and 4WD HIGH-4WD LOW switching are prohibited.)
    1. 4WD control ECU
    2. Brake actuator assembly (skid control ECU)
    2WD-4WD HIGH and 4WD HIGH-4WD LOW switching are prohibited.
    4HI and 4LO indicator light blinks
    U0122
    High-Low Switching Limitation
    (When there is a vehicle speed/automatic transmission signal malfunction, High-Low switching is prohibited.)
    1. 4WD control ECU
    2. ECM, Brake actuator assembly (skid control ECU)
    2WD-4WD HIGH and 4WD HIGH-4WD LOW switching are prohibited.
    4HI and 4LO indicator light blinks
    1. U0100
    2. U0122
    Engine ON/OFF Judgment
    (Changes control when engine is ON/OFF according to the engine speed.)
    1. 4WD control ECU
    2. ECM
    4WD HIGH-4WD LOW switching are prohibited.
    4HI and 4LO indicator light blinks
    U0100
    Shift Position Judgment
    1. 4WD control ECU
    2. ECM
    4WD HIGH-4WD LOW switching are prohibited.
    4HI and 4LO indicator light blinks
    U0100
    Indicator and Buzzer Signal Output
    (Outputs a signal indicating the state of the indicators and buzzers, which represents the actuator position and switching status.)
    1. 4WD control ECU
    2. -
    Cannot update the indicator and buzzer signals, as signal cannot be transmitted.
    Cannot update the indicator and buzzer signals, as signal cannot be transmitted.
    Nothing
    Electrical Load Control
    (Performs idle up according to the electrical load.)
    1. ECM
    2. Main body ECU (driver side junction block assembly), Air conditioning amplifier assembly
    Idle up according to the electrical load is not performed.
    The idling speed changes.
    Nothing
    Air Conditioning-linked Control
    (Performs idle up according to the compressor load. Performs air conditioning cut control.)
    1. ECM
    2. Air conditioning amplifier assembly
    Air conditioning-linked control does not operate.
    Air conditioning does not operate.
    Nothing
    Charging Control
    (Performs idle up according to charging requests.)
    1. ECM
    2. Main body ECU (driver side junction block assembly), Air conditioning amplifier assembly
    Idle up according to charging requests is not performed.
    Idle up according to charging requests is not performed.
    Nothing
    Integrated Control
    (Estimates the driver requested torque based on the accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are improved.)
    1. ECM
    2. Brake actuator assembly (skid control ECU), Steering angle sensor
    Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, drivability, acceleration performance and acceleration feeling are not improved.
    Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, drivability, acceleration performance and acceleration feeling are not improved.
    Nothing
    ECT System Indicator
    (Displays shift, switch and mode information to the meter.)
    1. ECM
    2. Main body ECU (driver side junction block assembly)
    Nothing
    ECT system indicators do not illuminate.
    Nothing
    AI-SHIFT Control
    (Controls the automatic transmission in order to improve engine braking power and acceleration feel.)
    1. ECM
    2. Brake actuator assembly (skid control ECU), Radio and display receiver assembly, Navigation receiver assembly
    AI-SHIFT control does not operate.
    AI-SHIFT control does not operate.
    Nothing
    Coast Downshift/Heater
    Requested Upshift Delay
    (Changes the coast downshift point based on the air conditioning load. Performs heater requested upshift delay.)
    1. ECM
    2. Air conditioning amplifier assembly
    Coast downshift does not operate.
    Coast downshift shock becomes stronger.
    Nothing
    Cruise Control
    (Adjusts the engine throttle valve opening amount automatically to control the vehicle.)
    1. ECM
    2. Brake actuator assembly (skid control ECU), Combination meter assembly
    Cruise control is not performed.
    1. When transmission is lost: The cruise main indicator light does not illuminate.
    2. When reception is lost: Cruise control is not performed.
    Nothing
    Engine Control
    (Performs fuel supply analysis and alcohol concentration learning.)
    1. ECM
    2. Combination meter assembly
    Alcohol concentration learning is not performed.
    Drivability worsens and the engine may stall due to the delay of alcohol concentration learning.
    U0155
    ABS control
    (Monitors for tire slippage and performs fluid pressure control to prevent the wheels from locking up in order to maintain vehicle stability and vehicle body deceleration.)
    1. Brake actuator assembly (skid control ECU)
    2. 4WD control ECU
    The ABS does not operate.
    ABS warning light turns on.
    U0073
    MSR control
    (Prevents the tires from slipping due to engine drag torque by increasing engine torque.)
    1. Brake actuator assembly (skid control ECU)
    2. ECM, Steering angle sensor, 4WD control ECU
    MSR does not operate.
    Light turns on.
    1. U0073
    2. U0100
    3. U0114
    4. U0123
    5. U0126
    TCS control
    (Prevents excessive tire slippage due to engine torque by decreasing engine torque and increasing pressure to the brakes.)
    1. Brake actuator assembly (skid control ECU)
    2. ECM, Steering angle sensor, 4WD control ECU
    TCS does not operate.
    Light turns on.
    1. U0073
    2. U0100
    3. U0114
    4. U0123
    5. U0126
    VSC control
    (Reduces excess yaw by increasing brake pressure, and induces necessary yaw by increasing brake pressure and reducing engine torque.)
    1. Brake actuator assembly (skid control ECU)
    2. ECM, Steering angle sensor, 4WD control ECU
    VSC does not operate.
    Light turns on.
    1. U0073
    2. U0100
    3. U0114
    4. U0123
    5. U0126
    Memory Mirror
    1. Memorizes and recalls the mirror position.
    2. Retracts the mirrors electronically.
    1. Outer mirror control ECU assembly
    2. ECM, Main body ECU (driver side junction block assembly), Front power seat ECU and switch LH
    1. When communication is lost with the ECM, mirror position memorization cannot be performed.
    2. When communication is lost with the main body ECU: Manual and automatic mirror retraction cannot be performed.
    3. When communication is lost with the front power seat ECU and switch LH: The position cannot be memorized or recalled.
    Nothing
    Nothing
    Steering sensor
    (Detects the steering wheel angle.)
    1. Steering angle sensor
    2. Brake actuator assembly (skid control ECU)
    Periodically sends STR1S01 (STS0=1) every 12 milliseconds.
    Brake warning light turns on.
    Nothing
    Auto away/return control
    (Controls the auto away/return operation according to the SKSW and IG signals. Prohibits auto away/return control.)
    1. Multiplex tilt and telescopic ECU
    2. Main body ECU (driver side junction block assembly), Combination meter assembly, Bus buffer ECU
    The memorization, recall, auto-return and auto-away functions do not operate.
    Nothing
    1. B2621
    2. B2624
    Memorization/recall control
    (Controls the steering wheel position memorization and recall for the seat position memory.)
    1. Multiplex tilt and telescopic ECU
    2. Front power seat control ECU and switch LH
    Memorization/recall control does not operate.
    Nothing
    B2621
    TC DTC output service
    (While TC = ON is being received from the engine, a DTC is output in response to the request from the combination meter assembly.)
    1. Combination meter assembly
    2. ECM
    If the TC signal is lost during TC service (TC=ON), the TC is determined to be OFF and TC service ends.
    Nothing
    Nothing
    Event Data Recorder (12 EDR)
    (Records conditions such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.)
    1. Center airbag sensor assembly
    2. ECM, Brake actuator assembly (skid control ECU), Steering angle sensor
    1. When reception is lost, an invalid value is recorded in the EDR.
    2. When there is a periodic problem, the previous value is maintained.
    Nothing
    Nothing
    Airbag Warning Light Control
    (Sends airbag warning light illumination information.)
    1. Combination meter assembly
    2. Center airbag sensor assembly
    -
    Nothing
    Nothing
    Collision Detection Signal
    (Notifies the system of a collision in order to perform fuel cut when a vehicle collision occurs.)
    1. ECM
    2. Center airbag sensor assembly
    -
    Nothing
    Nothing
    Seat Belt Warning Control
    (Sends information about the passengers in order to turn the seat belt warning on and off.)
    1. Main body ECU (driver side junction block assembly), Combination meter assembly
    2. Center airbag sensor assembly
    -
    Nothing
    Nothing
    Tachometer
    (Controls the tachometer according to engine speed signals.)
    1. Combination meter assembly
    2. ECM
    The tachometer displays 0 rpm.
    Nothing
    Nothing
    Speedometer
    (Controls the speedometer according to vehicle speed signals.)
    1. Combination meter assembly
    2. Brake actuator assembly (skid control ECU)
    The speedometer displays 0 km/h (0 mph).
    Nothing
    Nothing
    Engine Coolant Temperature Gauge
    (Controls the temperature gauge according to the temperature signals.)
    1. Combination meter assembly
    2. ECM
    The temperature gauge needle is at the middle of the "C" mark or below.
    Nothing
    Nothing
    ODO/TRIP Meter
    (Indicates the driven distance in the combination meter according to the vehicle speed pulse signal summation value.)
    1. Combination meter assembly
    2. Brake actuator assembly (skid control ECU)
    The calculation stops and the last displayed value remains.
    Nothing
    Nothing
    Automatic Transmission Shift Indicator
    (Displays shift information according to the shift position signal.)
    1. Combination meter assembly
    2. ECM
    The automatic transmission shift indicator turns off.
    Nothing
    Nothing
    Brake Warning Light
    (Turns the brake warning light on and off.)
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU)
    The brake warning light illuminates.
    The brake warning light illuminates.
    Nothing
    SRS Warning Light
    (Turns the SRS warning light on and off.)
    1. Combination meter assembly
    2. Center airbag sensor assembly
    The SRS warning light illuminates.
    The SRS warning light illuminates.
    Nothing
    Driver Side Seat Belt Warning Light
    (Turns the driver side seat belt warning light on and off.)
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly)
    The driver side seat belt warning light illuminates.
    The driver side seat belt warning light illuminates.
    Nothing
    All Doors Open Light
    (Turns the all doors open light on and off.)
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly)
    The all doors open light illuminates.
    Nothing
    Nothing
    BEAM Indicator Light
    (Turns the BEAM indicator light on and off.)
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly)
    The BEAM indicator condition is maintained.
    Nothing
    Nothing
    TAIL Indicator Light
    (Turns the TAIL indicator light on and off.)
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly)
    The TAIL indicator condition is maintained.
    Nothing
    Nothing
    HEAD Indicator Light
    (Turns the HEAD indicator light on and off.)
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly)
    The HEAD indicator condition is maintained.
    Nothing
    Nothing
    CRUISE Main Indicator Light
    (Turns the CRUISE main indicator light on and off.)
    1. Combination meter assembly
    2. ECM
    The cruise main indicator condition is maintained.
    Nothing
    Nothing
    ABS Warning Light
    (Turns the ABS warning light on and off.)
    1. Combination meter assembly
    2. Brake actuator assembly (skid control ECU)
    The ABS warning light illuminates.
    The ABS warning light illuminates.
    Nothing
    VSC OFF Indicator Light
    (Turns the VSC OFF indicator light on and off.)
    1. Combination meter assembly
    2. Brake actuator assembly (skid control ECU)
    The VSC OFF indicator condition is maintained.
    Nothing
    Nothing
    SLIP Indicator Light
    (Turns the SLIP indicator light on and off.)
    1. Combination meter assembly
    2. Brake actuator assembly (skid control ECU)
    The slip indicator condition is maintained.
    Nothing
    Nothing
    4LO Warning Light
    (Turns the 4LO warning light on and off.)
    1. Combination meter assembly
    2. 4WD control ECU
    The 4LO indicator condition is maintained.
    Nothing
    Nothing
    4HI Warning Light
    (Turns the 4HI warning light on and off.)
    1. Combination meter assembly
    2. 4WD control ECU
    The 4HI indicator condition is maintained.
    Nothing
    Nothing
    Passenger Side Seat Belt Warning Light
    (Turns the passenger side seat belt warning light on and off.)
    1. Combination meter assembly
    2. Center airbag sensor assembly
    The passenger side seat belt warning light illuminates.
    Nothing
    Nothing
    Seat Belt Warning Buzzer
    Controls the seat belt warning buzzer to sound and not sound according to the various signals that are input.
    1. Combination meter assembly
    2. ECM, Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU), Center airbag sensor assembly
    The seat belt warning buzzer condition is maintained.
    Nothing
    Nothing
    Key Reminder Buzzer
    Controls the key reminder buzzer to sound and not sound according to the various signals that are input.
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly)
    The key reminder buzzer does not sound.
    Nothing
    Nothing
    Parking Brake Unreleased Warning Buzzer
    Controls the parking brake unreleased warning buzzer to sound and not sound according to the various signals that are input.
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU)
    The parking brake unreleased warning buzzer does not sound.
    Nothing
    Nothing
    Door Ajar Driving Warning Buzzer
    Controls the door ajar driving warning buzzer to sound and not sound according to the various signals that are input.
    1. Combination meter assembly
    2. Main body ECU (driver side junction block assembly), Brake actuator assembly (skid control ECU)
    The door ajar driving warning buzzer does not sound.
    Nothing
    Nothing
    Sequential Shift Reject Buzzer
    Controls the sequential shift reject buzzer to sound and not sound according to the various signals that are input.
    1. Combination meter assembly
    2. ECM
    The sequential shift reject buzzer condition is maintained.
    Nothing
    Nothing
    Alarm Control
    (Sounds various warnings.)
    1. Main body ECU (driver side junction block assembly)
    2. ECM, Bus buffer ECU
    1. If communication is lost with the ECM: Alarm cancellation according to the engine speed does not operate.
    2. When communication is lost with the bus buffer ECU, warning output does not operate.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Door Lock Control
    (Locks/unlocks the doors.)
    1. Main body ECU (driver side junction block assembly)
    2. ECM, Combination meter assembly, Center airbag sensor assembly, Bus buffer ECU
    1. If communication is lost with the combination meter assembly:
      1. The speed-sensitive automatic door lock function does not operate.
      2. The key lock-in prevention unlock function when the vehicle is being driven is permitted.
    2. When communication is lost with the ECM:
      1. The shift-linked automatic door unlock function does not operate.
      2. The shift-linked automatic door unlock switching using the manual switch does not operate.
      3. The key lock-in prevention unlock function when the engine is started is permitted.
    3. When communication is lost with the center airbag sensor assembly: Key-linked lock control prohibition when the seat belts are fastened is not possible.
    4. When communication is lost with the bus buffer ECU: KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Illumination Control
    (Performs illumination control.)
    1. Main body ECU (driver side junction block assembly)
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Power Window Control
    (Performs key off power window control.)
    1. Main body ECU (driver side junction block assembly)
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Light Control
    (Controls the display dimming and daytime running lights.)
    1. Main body ECU (driver side junction block assembly)
    2. ECM, Combination meter assembly
    1. When communication is lost with the ECM, daytime running light control is not performed.
    2. When communication is lost with the combination meter assembly, automatically performs display dimming control when tail mode is not canceled (when the light sensor illuminance signal value is less than the display dimming value, the interior displays and indicators are dimmed).
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Wireless
    (Controls the wireless lock/unlock functions.)
    1. Main body ECU (driver side junction block assembly)
    2. Bus buffer ECU
    KLEG is maintained.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Option Control
    (Controls optional wireless lock, answer-back optional illumination, alarm warning requests and dome light warning requests.)
    1. Main body ECU (driver side junction block assembly)
    2. Bus buffer ECU
    1. Optional wireless lock control does not operate.
    2. Answer-back control for optional illumination does not operate.
    3. Alarm warning request control does not operate.
    4. Dome light warning request control does not operate.
    Nothing
    1. U0199
    2. U0208
    3. U1002
    4. U1115
    Lock Control
    (Sends a door lock request signal.)
    1. Bus buffer ECU
    2. Main body ECU (driver side junction block assembly)
    Lock control is not performed.
    Nothing
    Nothing
    Air conditioning control
    (Requests air conditioning control by sending DFON and ACON signals.)
    1. Bus buffer ECU
    2. Air conditioning amplifier assembly
    Air conditioning control is not performed.
    Nothing
    Nothing
    Hazard answer-back control
    (Requests hazard blinking through the HZRD bit.)
    1. Bus buffer ECU
    2. Main body ECU (driver side junction block assembly)
    Hazard answer-back control is not performed.
    Nothing
    Nothing
    Eco Navigation Display
    (Displays the average fuel consumption history and a graph indicating the fuel consumption in 1 minute intervals.)
    1. Radio and display receiver assembly, Navigation receiver assembly
    2. Combination meter assembly
    1. Stops updating the average fuel consumption history on the eco navigation (eco drive screen).
    2. If the distance to empty is displayed on the eco navigation (eco drive) screen, the value for the distance to empty is cleared due to a distance to empty communication stop.
    1. The most recent value for the fuel consumption interval graph on the eco navigation (eco drive) screen is cleared.
    2. The numbers of the distance to empty displayed on the fuel consumption screen of the eco navigation (eco drive) display are cleared.
    U0155
    Destination Determination
    (Determines the destination based on the destination symbol and destination package information and selects the display language, time zone, etc.)
    1. Radio and display receiver assembly, Navigation receiver assembly
    2. Main body ECU (driver side junction block assembly)
    Determines the destination according to the last received value and operates accordingly (if there is no last received value, the system operates using the default value).
    The time zone and language selection screens do not match the destination.
    U0140
    Vehicle Customize Function
    (Changes the behavior and control parameters of various functions [illumination lighting time, etc.] according to user operation via the screen.)
    1. Radio and display receiver assembly, Navigation receiver assembly
    2. Main body ECU (driver side junction block assembly), Front power seat ECU and switch LH, Multiplex tilt and telescopic ECU
    3 retries are performed (including the first time).
    1. The customize options for items related to the main body ECU are not displayed or the setting cannot be changed.
    2. The customize options for items related to the front power seat ECU and switch LH are not displayed or the setting cannot be changed.
    3. The customize options for items related to the multiplex tilt and telescopic ECU are not displayed or the setting cannot be changed.
    1. B15F6
    2. B15F8
    ESPO
    (Displays the level of "eco" driving.)
    1. Radio and display receiver assembly, Navigation receiver assembly
    2. Center airbag sensor assembly, Air conditioning amplifier assembly, Main body ECU (driver side junction block assembly), Steering angle sensor
    Nothing
    Nothing
    Nothing
    Charging Station Reporting Service
    (Informs the user about charging stations within range from distance to empty based on information received from the G-BOOK center.)
    1. Radio and display receiver assembly, Navigation receiver assembly
    2. Combination meter assembly
    Stops providing information and resets values to the default.
    Cannot provide information.
    Nothing
    Meter-linked Function
    (Changes display based on customization information set through the meter. Outputs the customization information set in the system.)
    1. Radio and display receiver assembly, Navigation receiver assembly
    2. Combination meter assembly
    Maintains the last valid state.
    Nothing
    Nothing
    Blind Spot Monitor
    (Warns the driver when the system detects a vehicle in the blind spots of the outer mirrors.)
    1. Blind spot monitor sensor RH/LH
    2. ECM, Brake actuator assembly (skid control ECU), Main body ECU (driver side junction block assembly), Steering angle sensor, Blind spot monitor sensor RH/LH
    Nothing
    Blind spot monitor system warning displayed.
    1. U0100
    2. U0126
    3. U0129
    4. U0142
    5. U0232
    Relay Function
    (Transmits relay frames and does not transmit non-relay frames.)
    1. Network gateway ECU
    2. ECUs connected to V bus and V2 bus
    CAN controller is reset.
    Nothing
    Nothing
    Diagnostic Function
    (Determines the connection and communication status of ECUs which are connected to the V2 bus.)
    1. Network gateway ECU
    2. ECUs connected to V2 bus
    CAN controller is reset.
    Nothing
    1. U0233
    2. U1002
    NM Function
    (Performs communication via NM frames with ECUs that are equipped with NM, and controls the CAN communication sleep/wake up functions.)
    1. Network gateway ECU
    2. ECUs with NM functions connected to V bus and V2 bus
    1. CAN controller is reset.
    2. Enter LimpHome mode.
    Nothing
    Nothing
    CCP Function
    (Communicates with tools connected via the V bus and monitors the RAM in the gateway ECU.)
    1. Network gateway ECU
    2. Tools connected via V bus
    CAN controller is reset.
    Nothing
    Nothing