Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > TERMINALS OF ECU

for Preparation Click here



CHECK AIR CONDITIONING AMPLIFIER

B160781E01

  1. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Check from the rear of the connector with it connected to the air conditioning amplifier.


    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J19-1 (IG+) - J19-14 (GND)
    P - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V
    J19-21 (B) - J19-14 (GND)
    BR - W-B
    Battery power source
    Always
    11 to 14 V
    J19-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    J19-5 (TAM) - J19-14 (GND)
    V - W-B
    Ambient temperature sensor signal
    Ignition switch ON at 25°C (77°F)
    1.35 to 1.75 V
    Ignition switch ON at 40°C (104°F)
    0.9 to 1.2 V
    J19-8 (LOCK) - J19-14 (GND)
    SB - W-B
    Compressor lock sensor signal
    Engine is running
    Blower switch LO
    A/C switch ON
    Pulse generation
    (see waveform 1)
    J19-23 (BLW) - J19-14 (GND)
    LG - W-B
    Blower motor control signal
    Ignition switch ON
    Blower switch LO
    Pulse generation
    (see waveform 2)
    J19-20 (MGC) - J19-14 (GND)
    P - W-B
    Compressor magnetic clutch operation signal
    Engine is running
    Blower switch LO
    A/C switch OFF
    11 to 14 V
    Engine is running
    Blower switch LO
    A/C switch ON
    Below 1 V
    J19-33 (TSD) - J19-14 (GND)
    P - W-B
    Driver side solar sensor signal
    Ignition switch ON
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    J19-32 (TSP) - J19-14 (GND)
    L - W-B
    Passenger side solar sensor signal
    Ignition switch ON
    Solar sensor subjected to electric light
    0.8 to 4.3 V
    J19-29 (TR) - J19-34 (SG-1)
    G - B
    Room temperature sensor signal
    Ignition switch ON
    Front side interior temperature: 25°C (77°F)
    1.8 to 2.2 V
    J19-34 (SG-1) - Body ground
    B - Body ground
    Ground for room temperature sensor
    Always
    Below 1 Ω
    J19-13 (SG-2) - Body ground
    G - Body ground
    Ground for ambient temperature sensor
    Always
    Below 1 Ω
    J19-37 (LIN1) - J19-14 (GND)
    SB - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation
    J19-11 (CANH) - J19-14 (GND)
    B - W-B
    Hi-level CAN bus line
    Ignition switch ON
    Pulse generation
    (see waveform 3)
    J19-12 (CANL) - J19-14 (GND)
    W - W-B
    Lo-level CAN bus line
    Ignition switch ON
    Pulse generation
    (see waveform 4)
    z1-2 (BUS G) - Body ground
    -
    Ground for BUS IC
    Always
    Below 2 V
    z1-3 (BUS) - z1-2 (BUS G)
    -
    BUS IC control signal
    Ignition switch OFF → ON
    Pulse generation
    z1-4 (B BUS) - z1-2 (BUS G)
    -
    Power supply for BUS IC
    Always
    11 to 14 V
    z1-5 (SGA) - Body ground
    -
    Ground for No. 1 cooler thermistor
    Always
    Below 2 V
    z1-6 (TEA) - z1-5 (SGA)
    -
    No. 1 cooler thermistor signal
    Ignition switch ON
    No. 1 cooler thermistor at 0°C (32°F)
    1.7 to 2.1 V
    Ignition switch ON
    No. 1 cooler thermistor at 15°C (59°F)
    0.7 to 1.3 V
    1. If the result is not as specified, the ECU may have a malfunction.



  2. E147483E01
  3. Using an oscilloscope, check waveform 1.
    Compressor lock signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J19-8 (LOCK) - J19-14 (GND)
    200 mV/DIV., 10 ms./DIV.
    Engine is running
    Blower switch LO
    A/C switch ON



  4. E103396E08
  5. Using an oscilloscope, check waveform 2.
    Blower motor control signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J19-23 (BLW) - J19-14 (GND)
    1 V/DIV., 500 μsec./DIV.
    Ignition switch ON
    Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.



  6. A086154E10
  7. Using an oscilloscope, check waveform 3.
    CAN communication signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J19-11 (CANH) - J19-14 (GND)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  8. A086155E11
  9. Using an oscilloscope, check waveform 4.
    CAN communication signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J19-12 (CANL) - J19-14 (GND)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.


CHECK AIR CONDITIONING CONTROL ASSEMBLY

E280655E01

  1. Disconnect the J127 air conditioning control assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J127-4 (IG+) - J127-5 (GND)
    SB - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V
    J127-5 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    J127-7 (STX) - J127-5 (GND)
    SB - W-B
    LIN communication signal
    Ignition switch ON
    Pulse generation

    1. If the result is not as specified, there may be a malfunction on the wire harness side.