Home › BODY › EXTERIOR › REAR BUMPER (for Resin Type Bumper)

REAR BUMPER (for Resin Type Bumper) > DISASSEMBLY

for Preparation Click here



1. REMOVE REAR BUMPER PLATE LH


    B355013
  1. Detach the 3 claws and clip and remove the rear bumper plate LH.



2. REMOVE REAR BUMPER PLATE RH

HINT:
Use the same procedure described for the LH side.



3. REMOVE REAR BUMPER PAD SUB-ASSEMBLY LH


    B355014
  1. Remove the 3 clips.

  1. Detach the 12 claws and 2 guides and remove the rear bumper pad sub-assembly LH as shown in the illustration.



4. REMOVE LICENSE PLATE LIGHT ASSEMBLY LH


E281366
  1. Detach the 2 claws.



    E281367
  1. Disconnect the connector and remove the license plate light assembly LH.



5. REMOVE LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



6. REMOVE REAR BUMPER EXTENSION INSERT LH


    B355019
  1. Remove the 8 clips and rear bumper extension insert LH.



7. REMOVE REAR BUMPER EXTENSION INSERT RH

HINT:
Use the same procedure described for the LH side.



8. REMOVE BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


    B354805
  1. Disconnect the connector.

  1. Remove the 3 nuts and blind spot monitor sensor LH.



9. REMOVE BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor System)

HINT:
Use the same procedure described for the LH side.



10. REMOVE NO. 2 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)


  1. Detach the 4 claws and remove the No. 2 ultrasonic sensor as shown in the illustration.


    B354819

    HINT:
    The illustration shows the No. 2 ultrasonic sensor for the RH. The horizontal orientation of the No. 2 ultrasonic sensor for the LH is opposite that of the image shown in the illustration.



11. REMOVE NO. 3 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)


  1. Detach the 4 claws and remove the No. 3 ultrasonic sensor as shown in the illustration.


    B354819

    HINT:
    The illustration shows the No. 3 ultrasonic sensor for the RH. The horizontal orientation of the No. 3 ultrasonic sensor for the LH is opposite that of the image shown in the illustration.



12. REMOVE REAR BUMPER BAR CORNER REINFORCEMENT LH


    B355020
  1. Remove the 5 bolts and rear bumper bar corner reinforcement LH.



13. REMOVE REAR BUMPER BAR CORNER REINFORCEMENT RH

HINT:
Use the same procedure described for the LH side.



14. REMOVE NO. 2 FRAME WIRE


  1. w/ Towing Package:



    1. Detach all the clamps and remove the No. 2 frame wire from the receiver hitch bracket sub-assembly.


      B355017E01


      Text in Illustration 
      *A
      w/ Intuitive Parking Assist System
      *B
      w/o Intuitive Parking Assist System
      *C
      w/ Blind Spot Monitor System
      *D
      w/o Blind Spot Monitor System



  1. w/o Towing Package:



    1. Detach all the clamps and remove the No. 2 frame wire from the rear bumper reinforcement sub-assembly.


      B355018E01


      Text in Illustration 
      *A
      w/ Intuitive Parking Assist System
      *B
      w/o Intuitive Parking Assist System
      *C
      w/ Blind Spot Monitor System
      *D
      w/o Blind Spot Monitor System



15. REMOVE REAR BUMPER SIDE STAY LH


    B355024
  1. Remove the 5 bolts and rear bumper side stay LH.



16. REMOVE REAR BUMPER SIDE STAY RH

HINT:
Use the same procedure described for the LH side.



17. REMOVE REAR BUMPER PLATE


    B356290E01
  1. Remove the 2 bolts and rear bumper plate.
    Text in Illustration 
    *A
    w/ Towing Package
    *B
    w/o Towing Package



18. REMOVE REAR BUMPER UPPER COVER LH


    B355025
  1. Remove the 2 nuts and rear bumper upper cover LH.



19. REMOVE REAR BUMPER UPPER COVER RH

HINT:
Use the same procedure described for the LH side.