Home › BODY › EXTERIOR › REAR BUMPER (for Steel Type Bumper)

REAR BUMPER (for Steel Type Bumper) > REASSEMBLY

for Preparation Click here



1. INSTALL REAR BUMPER UPPER COVER LH
  1. Install the rear bumper upper cover LH with the 2 nuts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



2. INSTALL REAR BUMPER UPPER COVER RH

HINT:
Use the same procedure described for the LH side.



3. INSTALL REAR BUMPER BAR LH
  1. Install the rear bumper bar LH with the 5 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



4. INSTALL REAR BUMPER BAR RH

HINT:
Use the same procedure described for the LH side.



5. INSTALL REAR BUMPER PLATE
  1. Install the rear bumper plate with the 2 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



6. INSTALL NO. 2 FRAME WIRE
  1. w/ Towing Package:

    1. Attach all the clamps to install the No. 2 frame wire to the receiver hitch bracket sub-assembly.

  1. w/o Towing Package:

    1. Attach all the clamps to install the No. 2 frame wire to the rear bumper reinforcement sub-assembly.



7. INSTALL NO. 3 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)



B354822E01

  1. Attach the 4 claws to install the No. 3 ultrasonic sensor as shown in the illustration.
    Text in Illustration 
    *a
    No. 3 ultrasonic sensor direction
    *b
    Keyhole direction

    NOTICE:
    1. No. 3 ultrasonic sensor direction is the same as the keyhole direction.
    1. Do not damage the bumper with the protrusion when installing the No. 3 ultrasonic sensor.



8. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)


    B354820
  1. Install the No. 2 ultrasonic sensor retainer as shown in the illustration.



9. INSTALL NO. 2 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)


    B354821
  1. Install the No. 2 ultrasonic sensor as shown in the illustration.

    NOTICE:
    Do not damage the bumper with the protrusion when installing the No. 2 ultrasonic sensor.



10. INSTALL REAR BUMPER BAR CORNER REINFORCEMENT LH
  1. Install the rear bumper bar corner reinforcement LH with the 5 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



11. INSTALL REAR BUMPER BAR CORNER REINFORCEMENT RH

HINT:
Use the same procedure described for the LH side.



12. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH
  1. Connect the connector.

  1. Attach the 2 claws to install the license plate assembly LH.



13. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



14. INSTALL REAR BUMPER PAD SUB-ASSEMBLY LH
  1. Attach the 12 claws and 2 guides to install the rear bumper pad sub-assembly LH.

  1. Install the 3 clips.



15. INSTALL REAR BUMPER PLATE LH
  1. Attach the 3 claws and clip to install the rear bumper plate LH.



16. INSTALL REAR BUMPER PLATE RH

HINT:
Use the same procedure described for the LH side.