LIGHTING SYSTEM > Front Fog Light Circuit |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (FRONT FOG LIGHT) |
Operate the Techstream according to the steps on the display and select "Active Test".
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Front Fog Light Relay | Front fog light | ON or OFF | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT FUSE (FOG) |
Remove the FOG fuse from the engine room junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| FOG fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT BULB - BATTERY) |
![]() ![]() |
for LH:
Disconnect the A30 front fog light connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A30-2 - Body ground | Light control switch TAIL, front fog light switch ON | 11 to 14 V |
| Light control switch TAIL, front fog light switch OFF | Below 1 V |
for RH:
Disconnect the A31 front fog light connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A31-2 - Body ground | Light control switch TAIL, front fog light switch ON | 11 to 14 V |
| Light control switch TAIL, front fog light switch OFF | Below 1 V |
|
| ||||
| OK | ||
| ||
| 4.INSPECT FOG LIGHT RELAY (FOG) |
![]() |
Remove the fog light relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (FOG LIGHT RELAY - BATTERY) |
![]() |
Remove the fog light relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Fog light relay terminal 1 - Body ground | Light control switch TAIL | 11 to 14 V |
| Fog light relay terminal 3 - Body ground | Always |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (FR FOG RELAY - FRONT FOG LIGHT BULB) |

Remove the fog light relay from the engine room relay block.
Disconnect the A30*1 and A31*2 front fog light connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Fog light relay terminal 5 - A30-2*1 | Always | Below 1 Ω |
| Fog light relay terminal 5 - Body ground*1 | Always | 10 kΩ or higher |
| Fog light relay terminal 5 - A31-2*2 | Always | Below 1 Ω |
| Fog light relay terminal 5 - Body ground*2 | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK FRONT FOG LIGHT |
![]() |
Disconnect the J4 ECU connector.
Using a service wire, connect J4-4 (FFGO) on the wire harness side and body ground.
Check that the front fog light illuminates.
|
| ||||
| OK | ||
| ||