Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Headlight (HI-BEAM) Circuit

for Preparation Click here


DESCRIPTION

The main body ECU receives light control switch and dimmer switch information signals from the headlight dimmer switch, and illuminates the headlight high beam.

WIRING DIAGRAM


E286147E01


INSPECTION PROCEDURE

HINT:
Inspect the bulbs for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING TECHSTREAM (HEADLIGHT)
  1. Operate the Techstream according to the steps on the display and select "Active Test".

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Hi
    Headlight (High)
    ON or OFF
    -

    OK:
    Headlight (High) turns on / turns off.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT FUSE (HEAD LH, HEAD RH)
  1. Remove the HEAD LH and HEAD RH fuses from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    HEAD LH fuse
    Always
    Below 1 Ω
    HEAD RH fuse



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (HEADLIGHT HIGH BULB - BATTERY)
E282178E01
E282178E03
  1. for LH:

    1. Disconnect the A8 headlight connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A8-2 (HI) - Body ground
      Light control switch HEAD, dimmer switch High
      11 to 14 V
      Light control switch HEAD, dimmer switch except High
      Below 1 V

  1. for RH:

    1. Disconnect the A9 headlight connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      A9-2 (HI) - Body ground
      Light control switch HEAD, dimmer switch High
      11 to 14 V
      Light control switch HEAD, dimmer switch except High
      Below 1 V



NG
Go to step 4
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT HIGH BULB - BODY GROUND) 

4.INSPECT HEADLIGHT DIMMER RELAY (DIM)
E277741E01
  1. Remove the headlight dimmer relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω
    3 - 4
    Battery voltage not applied to terminals 1 and 2
    Below 1 Ω
    Battery voltage applied to terminals 1 and 2
    10 kΩ or higher



NG
REPLACE HEADLIGHT DIMMER RELAY
OK


5.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - BATTERY)
E147138E04
  1. Remove the headlight dimmer relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Headlight dimmer relay terminal 1 - Body ground
    Light control switch HEAD, dimmer switch High
    11 to 14 V
    Headlight dimmer relay terminal 3 - Body ground
    Light control switch HEAD, dimmer switch High



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER RELAY - HEADLIGHT HIGH BULB)

E282179E01

  1. Remove the headlight dimmer relay from the engine room relay block.

  1. for LH:

    1. Disconnect the A8 headlight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Headlight dimmer relay terminal 5 - A8-2 (HI)
      Always
      Below 1 Ω
      Headlight dimmer relay terminal 5 - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the A9 headlight connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      Headlight dimmer relay terminal 5 - A9-2 (HI)
      Always
      Below 1 Ω
      Headlight dimmer relay terminal 5 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HEADLIGHT (HIGH BEAM)
E147118E11
  1. Disconnect the DB ECU connector.

  1. Using a service wire, connect DB-16 (DIM) on the wire harness side and body ground.

  1. Check that the headlight high beam illuminates.

    OK:
    Headlight high beam illuminates.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HEADLIGHT DIMMER RELAY - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU