Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM

ENGINE IMMOBILISER SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK TRANSPONDER KEY AMPLIFIER

B167608E01

  1. Disconnect the J20 amplifier connector.

  2. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J20-7 (AGND) - Body ground
    GR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the J20 amplifier connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J20-1 (VC5) - J20-7 (AGND)
    G - GR
    Power supply
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    4.6 to 5.4 V
    J20-4 (CODE) - J20-7 (AGND)
    LG - GR
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 1)
    J20-5 (TXCT) - J20-7 (AGND)
    L - GR
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 2)
    J20-7 (AGND) - Body ground
    GR - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, the amplifier may have a malfunction.



  5. B069240E24
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference): 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J20-4 (CODE) - J20-7 (AGND)
    5 V/DIV., 20 msec./DIV.
    Key inserted in ignition key cylinder



  7. B069239E20
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference): 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J20-5 (TXCT) - J20-7 (AGND)
    5 V/DIV., 20 msec./DIV.
    Key inserted in ignition key cylinder


CHECK TRANSPONDER KEY ECU

B121962E08

  1. Disconnect the J26 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J26-16 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    J26-1 (+B) - J26-16 (GND)
    G - W-B
    Battery
    Always
    11 to 14 V
    J26-2 (IG) - J26-16 (GND)
    GR - W-B
    Ignition switch
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    J26-3 (KSW) - J26-16 (GND)
    LG - W-B
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    Key inserted in ignition key cylinder
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the J26 ECU connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J26-14 (VC5) - J26-16 (GND)
    G - W-B
    Power source
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    4.6 to 5.4 V
    J26-7 (CTY) - J26-16 (GND)
    Y - W-B
    Door courtesy
    Door closed
    10 kΩ or higher
    Door open
    Below 1 Ω
    J26-4 (TXCT) - J26-16 (GND)
    L - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 1)
    J26-15 (CODE) - J26-16 (GND)
    LG - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (see waveform 2)
    J26-13 (EFIO) - J26-16 (GND)
    Y - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (see waveform 3)
    J26-12 (EFII) - J26-16 (GND)
    SB - W-B
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
    Pulse generation (see waveform 4)
    J26-8 (IND) - J26-16 (GND)
    V - W-B
    Security indicator light signal
    Immobiliser set status
    Alternating between 11 to 14 V and below 1 V
    Immobiliser unset status
    Below 1 V
    J26-9 (D) - J26-16 (GND)
    BE - W-B
    Diagnosis tester communication
    Always
    Pulse generation
    If the result is not as specified, the ECU may have a malfunction.



  5. B069239E21
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference): 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J26-4 (TXCT) - J26-16 (GND)
    5 V/DIV., 20 msec./DIV.
    Key inserted in ignition key cylinder



  7. B069240E25
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference): 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J26-15 (CODE) - J26-16 (GND)
    5 V/DIV., 20 msec./DIV.
    Key inserted in ignition key cylinder



  9. B069241E17
  10. Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference): 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J26-13 (EFIO) - J26-16 (GND)
    10 V/DIV., 100 msec./DIV.
    Ignition switch ON



  11. B229710E21
  12. Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference): 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    J26-12 (EFII) - J26-16 (GND)
    5 V/DIV., 500 msec./DIV.
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected