Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
  1. Raise the reclining adjuster release handle LH to reveal the claw.



    B354549E01
  1. Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape



2. REMOVE FRONT SEAT CUSHION SHIELD LH


    B354550
  1. Disconnect the 2 rubber bands.



    B354551E01
  1. Remove the 3 screws.

  1. Detach the guide, clip and 2 claws as indicated by the arrows in the order shown in the illustration to remove the front seat cushion shield LH.



3. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)


  1. for Manual Seat:



      B354553
    1. Detach the 2 hooks of the separate type front seat cushion cover.



    2. B354554E01
    3. Disconnect the connector and detach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp



    4. B354555
    5. Detach the wire harness clamp.

    6. Remove the nut and front seat inner belt assembly LH.



  1. for Power Seat:



      B354885E01
    1. Detach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp



    2. B354886
    3. Disconnect the connector and detach the wire harness clamp.

    4. Remove the nut and front seat inner belt assembly LH.



4. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)


    B355848
  1. Disconnect the connector and detach the wire harness clamp.

  1. Remove the nut and front seat inner belt assembly RH.



5. REMOVE SEAT POSITION AIRBAG SENSOR


    B355987
  1. for Manual Seat:

    1. Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position airbag sensor.



    B355989
  1. for Power Seat:

    1. Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position airbag sensor.



6. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD LH


    B354556
  1. Remove the 2 screws.

  1. Detach the guide in the direction indicated by the arrow shown in the illustration to remove the front inner No. 1 seat cushion shield LH.



7. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    B354558
  1. w/ Seat Heater System:

    1. Disconnect the connector.

    2. Detach the wire harness clamp to disconnect the wire harness of the front seatback heater assembly RH.



    B354559E01
  1. Detach the connector clamp and 3 wire harness clamps to disconnect the wire harness of the front seat airbag assembly LH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp



    B354560
  1. Remove the 4 bolts and separate type front seatback assembly.



8. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    B354561
  1. Detach the hook.



    B354562
  1. Pull out the wire harness from the separate type front seatback cover.



    B354563
  1. Open the 2 fasteners.



    B354564
  1. Detach the 2 hooks.

    1. Remove the 4 clips.

    2. Slide each hook to detach them.

  1. Pull out the 4 straps of the separate type front seatback cover from the separate type front seatback pad.



    B354568E01
  1. Detach the 6 fasteners to remove the separate type front seatback cover from the separate type front seatback pad.
    Text in Illustration 
    *1
    Fastener



    B354565
  1. Remove the 2 hog rings.



    B354567
  1. Detach the 4 claws to remove the 2 front seat headrest supports.

  1. Remove the separate type front seatback cover from the separate type front seatback pad.



9. REMOVE FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)


    B356060
  1. Remove the 8 tack pins to remove the front seatback heater assembly RH.



10. REMOVE SEPARATE TYPE FRONT SEATBACK PAD
  1. Remove the separate type front seatback pad from the front seatback frame sub-assembly LH.



11. REMOVE FRONT SEAT AIRBAG ASSEMBLY LH


    B355990
  1. Detach the 2 clamps from the front seatback main frame sub-assembly.

  1. Remove the 2 nuts and front seat airbag assembly LH.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the front seat back main frame sub-assembly is not deformed. If it is, replace it with a new one.



12. REMOVE RECLINING CONTROL LEVER LH


    B354569
  1. Remove the bolt and reclining control lever LH.



13. REMOVE FRONT SEATBACK SPRING ASSEMBLY


    B354570
  1. Detach the 2 clips and 2 guides to remove the front seatback spring assembly.



14. REMOVE FRONT SEATBACK HOOK
  1. Remove the 2 front seatback hooks from the front seatback spring assembly.



15. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


  1. Detach the 12 hooks and remove the separate type front seat cushion cover with pad.


    B354571



16. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
  1. Detach the 2 fasteners.



    B354572E01
  1. Remove the 10 hog rings and separate type front seat cushion cover.
    Text in Illustration 
    *1
    Fastener



17. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)


    B356063
  1. Detach the 10 tack pins to remove the front seat cushion heater assembly RH.



18. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)


    B166513
  1. Disconnect the connector.

  1. Detach the claw and remove the occupant classification ECU from the front seat assembly RH.



19. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)


    B355846
  1. Disconnect the connector.

  1. Detach the clamp to remove the seat heater control sub-assembly RH.



20. REMOVE FRONT SEAT CUSHION WIRE RH (for Front Passenger Side)


    B354574E01
  1. Disconnect the 4 connectors.

  1. Detach the connector clamp and 5 wire harness clamps to remove the front seat cushion wire RH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp



21. REMOVE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY


    B354575
  1. Detach the hook of the front side.



    B354576
  1. Detach the 4 hooks of the rear side to remove the separate type front seat cushion spring assembly.



22. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH


    B354577
  1. Detach the 2 claws to remove the front lower seat cushion shield LH.



23. REMOVE FRONT LOWER SEAT CUSHION SHIELD RH

HINT:
Use the same procedure described for the LH side.



24. REMOVE UPPER SEAT TRACK COVER


    B354578
  1. Detach the 2 claws to remove the upper seat track cover.

    HINT:
    Use the same procedure for all upper seat track covers.



25. REMOVE UPPER NO. 4 SEAT TRACK COVER


    B354579
  1. Detach the 2 claws to remove the upper No. 4 seat track cover.



26. REMOVE UPPER NO. 3 SEAT TRACK COVER

HINT:
Use the same procedure described for the upper No. 4 seat track cover.