Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL UPPER NO. 4 SEAT TRACK COVER
  1. Attach the 2 claws to install the upper No. 4 seat track cover.



2. INSTALL UPPER NO. 3 SEAT TRACK COVER

HINT:
Use the same procedure described for the upper No. 4 seat track cover.



3. INSTALL UPPER SEAT TRACK COVER
  1. Attach the 2 claws to install the upper seat track cover.

    HINT:
    Use the same procedure for all upper seat track covers.



4. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
  1. Attach the 2 claws to install the front lower seat cushion shield LH.



5. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

HINT:
Use the same procedure described for the LH side.



6. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
  1. Attach the 4 hooks of the rear side to install the separate type front seat cushion spring assembly.

  1. Attach the hook of the front side.



7. INSTALL FRONT SEAT CUSHION WIRE RH (for Front Passenger Side)


    B354574E01
  1. Attach the connector clamp and 5 wire harness clamps to install the front seat cushion wire RH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp

  1. Connect the 4 connectors.



8. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)
  1. Attach the clamp to install the seat heater control sub-assembly RH.

  1. Connect the connector.



9. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)
  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Attach the claw and install the occupant detection ECU to the front seat assembly RH.

    NOTICE:
    1. If the occupant detection ECU has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the occupant detection ECU, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the occupant classification ECU.



10. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
  1. Set the front seat cushion heater assembly LH on the separate type front seat cushion cover.



    B356063
  1. Using a tacker, install the front seat cushion heater assembly LH to the separate type front seat cushion cover with 10 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.



11. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
  1. Set the separate type front seat cushion cover in place.



    B354573E01
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 10 new hog rings as shown in the illustration.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    HINT:
    Install the hog rings at the cutouts if they are there.

  1. Attach the 2 fasteners.
    Text in Illustration 
    *1
    Fastener
    *2
    Hog Ring Pliers
    *a
    Cutout



12. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


  1. Attach the 12 hooks to install the separate type front seat cushion cover with pad.


    B354571



13. INSTALL FRONT SEATBACK HOOK
  1. Install the 2 front seatback hooks to the front seatback spring assembly.



14. INSTALL FRONT SEATBACK SPRING ASSEMBLY
  1. Attach the 2 guides and 2 clips to install the front seatback spring assembly.



15. INSTALL RECLINING CONTROL LEVER LH
  1. Install the reclining control lever LH with the bolt.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



16. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



    B360678
  1. Install the front seat airbag assembly LH with 2 new nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Connect the 2 clamps.



17. INSTALL SEPARATE TYPE FRONT SEATBACK PAD
  1. Install the separate type front seatback pad to the front seatback frame sub-assembly LH.



18. INSTALL FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)
  1. Set the front seatback heater assembly RH on the separate type front seatback cover.



    B356060
  1. Using a tacker, install the front seatback heater assembly RH to the separate type front seatback cover with 8 new tack pins as shown in the illustration.

    NOTICE:
    Do not substitute other metal parts for tack pins.



19. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
  1. Set the separate type front seatback cover in place.

  1. Attach the 4 claws to install the 2 front seat headrest supports.



    B354566E01
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    HINT:
    Install the hog rings at the cutouts if they are there.

    Text in Illustration 
    *1
    Hog Ring Pliers
    *a
    Cutout



    B354568E01
  1. Attach the 6 fasteners.
    Text in Illustration 
    *1
    Fastener

  1. Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.

  1. Attach the 2 hooks.

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after attaching the 2 hooks.
    3. Attach the 2 hooks securely.


    1. Slide each hook to attach them.

    2. Install the 4 clips.



    B356803
  1. Close the 2 fasteners.

  1. Pass the wire harness through the separate type front seatback cover.

  1. Attach the hook.



20. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. When reusing a bolt:

    1. Clean the threads of the bolt with non-residue solvent.

    2. Apply adhesive to the threads of the bolt.

      Adhesive:
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



    B354560
  1. Install the separate type front seatback assembly with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



    B354559E01
  1. Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly LH.
    Text in Illustration 
    *1
    Connector Clamp
    *2
    Wire Harness Clamp

  1. w/ Seat Heater System:

    1. Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly RH.

    2. Connect the connector.



21. INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH


    B354557
  1. Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.

  1. Install the 2 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



22. INSTALL SEAT POSITION AIRBAG SENSOR


    C107067E19
  1. Using a 1.0 mm (0.0393 in.) feeler gauge, temporarily install the seat position airbag sensor.
    Text in Illustration 
    *1
    1.0 mm
    *2
    Seat Position Airbag Sensor
    *3
    Feeler Gauge
    *4
    Seat Rail

    NOTICE:
    1. If the seat position airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position airbag sensor with a new one.
    2. When installing the seat position airbag sensor, be careful that the SRS wiring does not interfere with or is pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position airbag sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Using a T30 "TORX" socket wrench, tighten the "TORX" screw to install the seat position airbag sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position airbag sensor and the seat rail is within 0.6 to 1.4 mm (0.0236 to 0.0551 in.).

  1. Connect the connector.

  1. Check that there is no looseness in the installation parts of the seat position airbag sensor.



23. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)


  1. for Manual Seat:



      B356070E01
    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor of the front seat inner belt assembly LH to overlap the protruding part of the separate type front seat cushion spring assembly.

      Text in Illustration 
      *1
      Protruding Part

    2. Attach the wire harness clamp.



    3. B354554E01
    4. Connect the connector and attach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp

    5. Attach the 2 hooks of the separate type front seat cushion cover.



  1. for Power Seat:



      B356091E01
    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not allow the anchor of the front seat inner belt assembly LH to overlap the protruding part of the separate type front seat cushion spring assembly.

      Text in Illustration 
      *1
      Protruding Part

    2. Attach the wire harness clamp and connect the connector.



    3. B354885E01
    4. Attach the connector clamp and 3 wire harness clamps.
      Text in Illustration 
      *1
      Connector Clamp
      *2
      Wire Harness Clamp



24. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)


    B356071E01
  1. Install the front seat inner belt assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor of the front seat inner belt assembly RH to overlap the protruding part of the separate type front seat cushion spring assembly.

    Text in Illustration 
    *1
    Protruding Part

  1. Connect the connector and attach the connector clamp.



25. INSTALL FRONT SEAT CUSHION SHIELD LH


    B354552E01
  1. Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration to install the front seat cushion shield LH.

  1. Install the 3 screws.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Connect the 2 rubber bands.



26. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
  1. Attach the claw to install the reclining adjuster release handle LH.