Home › BODY › SEAT › POWER SEAT SWITCH (w/o Seat Position Memory System)

POWER SEAT SWITCH (w/o Seat Position Memory System) > INSPECTION

for Preparation Click here



1. INSPECT FRONT POWER SEAT SWITCH LH


  1. Check the resistance of the front power seat switch LH.



      B239569E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Slide Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      5 (SLDF) - 8 (B)
      5 (SLDF) - 7 (B1)
      Front position
      Below 1 Ω
      2 (SLDR) - 11 (E)
      2 (SLDR) - 12 (E1)
      5 (SLDF) - 11 (E)
      5 (SLDF) - 12 (E1)
      Neutral
      2 (SLDR) - 11 (E)
      2 (SLDR) - 12 (E1)
      5 (SLDF) - 11 (E)
      5 (SLDF) - 12 (E1)
      Rear position
      2 (SLDR) - 8 (B)
      2 (SLDR) - 7 (B1)
      Front Vertical Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      1 (FUP) - 8 (B)
      1 (FUP) - 7 (B1)
      Up position
      Below 1 Ω
      6 (FDWN) - 11 (E)
      6 (FDWN) - 12 (E1)
      1 (FUP) - 11 (E)
      1 (FUP) - 12 (E1)
      Neutral
      6 (FDWN) - 11 (E)
      6 (FDWN) - 12 (E1)
      1 (FUP) - 11 (E)
      1 (FUP) - 12 (E1)
      Down position
      6 (FDWN) - 8 (B)
      6 (FDWN) - 7 (B1)
      Lifter Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (LUP) - 8 (B)
      3 (LUP) - 7 (B1)
      Up position
      Below 1 Ω
      4 (LDWN) - 11 (E)
      4 (LDWN) - 12 (E1)
      3 (LUP) - 11 (E)
      3 (LUP) - 12 (E1)
      Neutral
      4 (LDWN) - 11 (E)
      4 (LDWN) - 12 (E1)
      3 (LUP) - 11 (E)
      3 (LUP) - 12 (E1)
      Down position
      4 (LDWN) - 8 (B)
      4 (LDWN) - 7 (B1)
      Reclining Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      8 (B) - 10 (RCLF)
      7 (B1) - 10 (RCLF)
      Front position
      Below 1 Ω
      9 (RCLR) - 11 (E)
      9 (RCLR) - 12 (E1)
      10 (RCLF) - 11 (E)
      10 (RCLF) - 12 (E1)
      Neutral
      9 (RCLR) - 11 (E)
      9 (RCLR) - 12 (E1)
      10 (RCLF) - 11 (E)
      10 (RCLF) - 12 (E1)
      Rear position
      8 (B) - 9 (RCLR)
      7 (B1) - 9 (RCLR)

      If the result is not as specified, replace the front power seat switch LH.
      Text in Illustration 
      *1
      Front Vertical Switch
      *2
      Slide Switch
      *3
      Lifter Switch
      *4
      Reclining Switch
      *a
      Component without harness connected
      (Front Power Seat Switch LH)



2. INSPECT FRONT POWER SEAT SWITCH RH


  1. Check the resistance of the front power seat switch RH.



      B241813E03
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Slide Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (SLDF) - 13 (B)
      2 (SLDF) - 14 (B1)
      Front position
      Below 1 Ω
      5 (SLDR) - 10 (E)
      5 (SLDR) - 9 (E1)
      2 (SLDF) - 10 (E)
      2 (SLDF) - 9 (E1)
      Neutral
      5 (SLDR) - 10 (E)
      5 (SLDR) - 9 (E1)
      2 (SLDF) - 10 (E)
      2 (SLDF) - 9 (E1)
      Rear position
      5 (SLDR) - 13 (B)
      5 (SLDR) - 14 (B1)
      Reclining Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      11 (RCLF) - 13 (B)
      11 (RCLF) - 14 (B1)
      Front position
      Below 1 Ω
      10 (E) - 12 (RCLR)
      9 (E1) - 12 (RCLR)
      10 (E) - 11 (RCLF)
      9 (E1) - 11 (RCLF)
      Neutral
      12 (RCLR) - 10 (E)
      12 (RCLR) - 9 (E1)
      10 (E) - 11 (RCLF)
      9 (E1) - 11 (RCLF)
      Rear position
      12 (RCLR) - 13 (B)
      12 (RCLR) - 14 (B1)

      If the result is not as specified, replace the front power seat switch.
      Text in Illustration 
      *1
      Slide Switch
      *2
      Reclining Switch
      *a
      Component without harness connected
      (Front Power Seat Switch RH)