Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › SPIRAL CABLE

SPIRAL CABLE > INSTALLATION

for Preparation Click here



1. INSTALL SPIRAL CABLE SUB-ASSEMBLY


    B166448
  1. Attach the 3 claws and install the spiral cable sub-assembly with steering sensor.

    NOTICE:
    When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel.

  1. Connect the connectors to the spiral cable sub-assembly with steering sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



2. INSTALL UPPER STEERING COLUMN COVER


    C290068
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



3. INSTALL LOWER STEERING COLUMN COVER


    C290067
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



4. ADJUST SPIRAL CABLE


    B166449
  1. Check that the ignition switch is OFF.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Rotate the spiral cable sub-assembly with steering sensor counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable sub-assembly with steering sensor by the airbag wire harness.



    B166450
  1. Rotate the spiral cable sub-assembly with steering sensor clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable sub-assembly with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable sub-assembly with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.



5. INSTALL STEERING WHEEL ASSEMBLY


    C290071E01
  1. Align the matchmarks on the steering wheel and steering main shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



6. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Support the steering pad with one hand.



    B354950
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the 2 airbag connector locks to install the 2 airbag connectors.

  1. Connect the horn connector to the steering pad.

  1. Install the steering pad.



    B360541
  1. Using T30 "TORX" socked wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



7. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B355450
  1. Attach the guide and claw to install the lower No. 3 steering wheel cover.



8. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B355451
  1. w/ Cruise Control:

    1. Attach the guide and claw to install the lower No. 2 steering wheel cover.



    B356801
  1. w/o Cruise Control:

    1. Attach the guide and claw to install the lower No. 2 steering wheel cover.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



10. INSPECT STEERING PAD
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    Cuts, small cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.
    If the horn does not sound, inspect the horn system.



11. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).