SIDE MOULDING > INSTALLATION |
| 1. INSTALL REAR BODY NO. 3 PROTECTOR LH |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Rear Body No. 3 Protector LH | 20 to 30°C (68 to 86°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Installation temperature
When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame, etc.) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is higher than 35°C (95°F), cool the vehicle body surface (installation surface of the door frame, etc.) and tape to between 20 and 30°C (68 and 86°F) prior to installation.
Before installation
Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame, etc.) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.
Key points for handling the tape
The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.
Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface)
To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

| *1 | Squeegee | *2 | Rear Body No. 3 Protector LH |
| *3 | Release Paper | *4 | Application Tape |
| *a | Sectional View | *b | Non-padded Side |
| *c | Padded Side | *d | Pressing |
| *e | Pulling | - | - |
Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners)
Remove the release paper and apply the tape carefully with your fingers.
Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles in the tape and achieve a neat finish.
Check after installation
After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.
for Regular Cab:
![]() |
Using a heat light, heat the vehicle body and a new rear body No. 3 protector LH.
Remove the peeling paper from the face of the rear body No. 3 protector LH.
Align the rear body No. 3 protector LH as shown in the illustration and using a squeegee, apply the rear body No. 3 protector LH.
Remove the application tape from the face of the rear body No. 3 protector LH.
for Double Cab:
![]() |
Using a heat light, heat the vehicle body and a new rear body No. 3 protector LH.
Remove the peeling paper from the face of the rear body No. 3 protector LH.
Align the rear body No. 3 protector LH as shown in the illustration and using a squeegee, apply the rear body No. 3 protector LH.
Remove the application tape from the face of the rear body No. 3 protector LH.
for CrewMax:
![]() |
Using a heat light, heat the vehicle body and a new rear body No. 3 protector LH.
Remove the peeling paper from the face of the rear body No. 3 protector LH.
Align the rear body No. 3 protector LH as shown in the illustration and using a squeegee, apply the rear body No. 3 protector LH.
Remove the application tape from the face of the rear body No. 3 protector LH.
| 2. INSTALL LOWER NO. 1 SIDE PANEL MOULDING LH |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Lower No. 1 Side Panel Moulding LH | 20 to 30°C (68 to 86°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
for Regular Cab:
Using a heat light, heat the vehicle body and lower No. 1 side panel moulding LH.
Remove the peeling paper from the face of the lower No. 1 side panel moulding LH.
Attach the 2 clips to install a new lower No. 1 side panel moulding LH.
for Double Cab:
Using a heat light, heat the vehicle body and lower No. 1 side panel moulding LH.
Remove the peeling paper from the face of the lower No. 1 side panel moulding LH.
Attach the 2 clips to install a new lower No. 1 side panel moulding LH.
for CrewMax:
Using a heat light, heat the vehicle body and lower No. 1 side panel moulding LH.
Remove the peeling paper from the face of the lower No. 1 side panel moulding LH.
Attach the 2 clips to install a new lower No. 1 side panel moulding LH.