Home › BODY › EXTERIOR › SIDE MOULDING

SIDE MOULDING > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedures listed below are for the LH side.



1. REMOVE LOWER NO. 1 SIDE PANEL MOULDING LH

HINT:
When removing the lower No. 1 side panel moulding LH, heat the vehicle body and lower No. 1 side panel moulding LH using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Lower No. 1 Side Panel Moulding LH
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body and lower No. 1 side panel moulding LH excessively.



  1. for Regular Cab:

    1. Using a heat light, heat the vehicle body and lower No. 1 side panel moulding LH.

    2. Put protective tape around the lower No. 1 side panel moulding LH.



    3. B356301E01
    4. Using a moulding remover, detach the 2 clips and remove the double-sided tape to remove the lower No. 1 side panel moulding LH.
      Text in Illustration 
      *1
      Protective Tape
      *2
      Double-sided Tape



  1. for Double Cab:

    1. Using a heat light, heat the vehicle body and lower No. 1 side panel moulding LH.

    2. Put protective tape around the lower No. 1 side panel moulding LH.



    3. B356302E01
    4. Using a moulding remover, detach the 2 clips and remove the double-sided tape to remove the lower No. 1 side panel moulding LH.
      Text in Illustration 
      *1
      Protective Tape
      *2
      Double-sided Tape



  1. for CrewMax:

    1. Using a heat light, heat the vehicle body and lower No. 1 side panel moulding LH.

    2. Put protective tape around the lower No. 1 side panel moulding LH.



    3. B356303E01
    4. Using a moulding remover, detach the 2 clips and remove the double-sided tape to remove the lower No. 1 side panel moulding LH.
      Text in Illustration 
      *1
      Protective Tape
      *2
      Double-sided Tape



2. REMOVE REAR BODY NO. 3 PROTECTOR LH

HINT:
When removing the rear body No. 3 protector LH, heat the vehicle body and rear body No. 3 protector LH using a heat light.

Standard:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Body No. 3 Protector LH
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or rear body No. 3 protector LH excessively.



  1. for Regular Cab:

    1. Using a heat light, heat the vehicle body and rear body No. 3 protector LH.



    2. B353302
    3. Pull back an edge of the rear body No. 3 protector LH and pull it parallel to the vehicle body to remove it.



  1. for Double Cab:

    1. Using a heat light, heat the vehicle body and rear body No. 3 protector LH.



    2. B353303
    3. Pull back an edge of the rear body No. 3 protector LH and pull it parallel to the vehicle body to remove it.



  1. for CrewMax:

    1. Using a heat light, heat the vehicle body and rear body No. 3 protector LH.



    2. B353304
    3. Pull back an edge of the rear body No. 3 protector LH and pull it parallel to the vehicle body to remove it.