Meter/Gauge:
Item
| Details
|
Speedometer
| Based on signal received from wheel speed sensor, skid control ECU calculates vehicle speed and transmits data to combination meter (CAN)
|
Tachometer
| Combination meter receives engine rpm signal from ECM, and gauge needle operates (CAN)
|
ODO/TRIP meter
| - Combination meter receives vehicle speed pulse integration signal from skid control ECU, and ODO/TRIP meter display operates (CAN)
- Using ODO/TRIP switch, ODO/TRIP meter display changes
|
Fuel receiver gauge
| Combination meter receives fuel amount information measured by fuel sender gauge, and gauge needle operates (Direct line)
|
Engine coolant temperature gauge
| Combination meter receives water temperature signal from ECM, and gauge needle operates (CAN)
|
Oil pressure receiver gauge*
| Combination meter receives engine rpm signal from ECM (CAN), and receives oil pressure sender signal from oil pressure sender (Direct line). Then meter measures signals and gauge needle operates.
|
Voltmeter*
| Monitors IG voltage and gauge needle operates (Direct line)
|
Warning/Indicator:
Item
| Details
|
BEAM indicator light

| Receives signal from main body ECU (CAN)
|
A/T OIL TEMP warning light*5

| Warning is displayed when oil temperature is high (CAN)
|
SRS warning light

| Receives malfunction signal from center airbag sensor (CAN)
|
DOOR indicator light

| Open door indicator comes on when signal is received from main body ECU (CAN)
|
Front seat belt warning light

| - Receives driver seat belt signal (Unfastened) from main body ECU (CAN)
- Receives front passenger seat belt signal (Unfastened) from center airbag sensor (CAN)
|
Brake warning light*2

| - Comes on when parking brake switch is ON (CAN)
- Brake fluid level warning switch is ON (Direct line)
- Vehicle stability control system is malfunctioning
|
Brake warning light*3

|
CHARGE warning light

| Receives malfunction signal from generator (Direct line)
|
4LO indicator light*1

| Receives 4LO signal from 4WD control ECU (CAN)
|
ABS warning light*2

| Receives malfunction signal from skid control ECU (CAN)
|
ABS warning light*3

|
MIL

| Receives malfunction signal from ECM (Direct line)
|
Low fuel warning light

| Receives fuel empty signal from fuel sender gauge (Direct line)
|
SLIP indicator light

| Receives malfunction signal from skid control ECU (CAN)
|
4HI indicator light*1

| Receives 4HI signal from 4WD control ECU (CAN)
|
Cruise control indicator light*9

| Receives cruise control on signal or malfunction signal from ECM (CAN)
|
SET indicator light*9

| Receives SET indicator light signal from ECM (CAN)
|
HEAD indicator light*2

| Receives taillight or headlight signal from main body ECU (CAN)
|
TAIL indicator light*3

| Receives taillight or headlight signal from main body ECU (CAN)
|
Turn signal indicator light (LH/RH)

| Receives turn signal from FLASHER relay (Direct line)
|
AUTO LSD indicator light

| Receives VSC OFF switch ON signal from skid control ECU (CAN)
|
VSC OFF indicator light

| Receives VSC control off signal or VSC system fail-safe control signal from skid control ECU (CAN)
|
TOW HAUL indicator light

| Receives towing indicator signal from main body ECU (CAN)
|
Tire pressure warning light

| Receives low tire pressure signal from tire pressure warning ECU (Direct line)
|
Oil pressure warning light*5

| Receives engine oil pressure warning signal from engine oil pressure switch (Direct line)
|
TRAC OFF indicator light*5

| Receives TRAC OFF indicator light signal from skid control ECU (CAN)
|
Master warning light*6

| Receives warning signal from each ECU (CAN)
|
Security indicator light*4

| Receives security warning light signal from transponder key ECU (Direct line)
|
Oil maintenance indicator light*2*5

| - Blinks when 4500 miles have been traveled, after ODO/TRIP switch is set (Direct line)
- Illuminates when 5000 miles have been traveled, after ODO/TRIP switch is set (Direct line)
|
Washer fluid level warning light*5

| Warning is displayed when the washer level is low (Direct line).
|
A/T P shift position indicator
| Receives P signal from ECM (Direct line)
|
A/T N shift position indicator
| Receives N signal from ECM (Direct line)
|
A/T D shift position indicator
| Receives D signal from ECM (Direct line)
|
A/T 6 shift position indicator*7
| Receives 6 signal from ECM (Direct line)
|
A/T 5 shift position indicator
| Receives 5 signal from ECM (CAN)
|
A/T 4 shift position indicator
| Receives 4 signal from ECM (CAN)
|
A/T 3 shift position indicator
| Receives 3 signal from ECM (CAN)
|
A/T 2 shift position indicator
| Receives 2 signal from ECM (CAN)
|
A/T 1 shift position indicator
| Receives 1 signal from ECM (CAN)
|
A/T S shift position indicator
| Receives S signal from ECM (Direct line)
|
A/T R shift position indicator
| Receives R signal from ECM (Direct line)
|