FRONT DOOR (for CrewMax) > REASSEMBLY |
| 1. INSTALL FRONT DOOR WEATHERSTRIP LH |
![]() |
Attach the 38 clips to install the weatherstrip.
| 2. INSTALL FRONT DOOR CHECK ASSEMBLY LH |
![]() |
Apply MP grease to the sliding areas of the door check.
Install the door check to the door panel with the 2 nuts.
Apply adhesive to the threads of the bolt.
Install the bolt.
| 3. INSTALL FRONT DOOR PANEL PROTECTOR LH |
![]() |
Attach the 8 clips to install the door panel protector.
| 4. INSTALL FRONT NO. 2 DOOR STIFFENER CUSHION |
![]() |
Install the stiffener cushion with the 2 clips.
| 5. INSTALL FRONT DOOR LOCK OPEN ROD LH |
Install the lock open rod to the outside handle frame.
| 6. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH |
![]() |
Slide the outside handle frame to install it.
Using a T30 "TORX" wrench, tighten the screw.
Install the front and rear outside handle pads.
| 7. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH |
![]() |
Install the handle by pushing it in the direction of the arrow in the illustration.
| 8. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH |
![]() |
Install the front door inside locking cable.
![]() |
Attach the 3 claws.
| 9. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH |
![]() |
Install the front door lock remote control cable.
| 10. INSTALL FRONT DOOR LOCK ASSEMBLY LH |
Apply MP grease to the sliding and rotating areas of the door lock.
Install a new door lock wire harness packing to the door lock.
![]() |
Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.
Connect the door lock connector.
| 11. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH |
![]() |
Using a T30 ''TORX'' socket, install the cover (with the door key cylinder) with the screw.
Install the hole plug.
| 12. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH |
![]() |
Install the frame with the 2 bolts.
| 13. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH |
![]() |
Install the frame with the 2 bolts.
| 14. INSTALL FRONT DOOR GLASS RUN LH |
![]() |
Install the front door glass run.
| 15. INSTALL FRONT OUTER DOOR GLASS WEATHERSTRIP ASSEMBLY LH |
![]() |
Attach the claw to install the weatherstrip.
| 16. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH |
![]() |
Install the side airbag sensor with the bolt.
Connect the connector.
| 17. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
![]() |
Apply MP grease to the sliding and rotating areas of the regulator motor.
Using a T25 ''TORX'' driver, install the motor with the 3 screws.
| 18. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
![]() |
Apply MP grease to the sliding and rotating areas of the window regulator.
Loosely install the temporary bolt onto the window regulator.
Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.
Temporarily install the window regulator with the 5 bolts, and tighten the temporary bolt so that it contacts the door panel.
Tighten the 6 bolts in the order shown in the illustration.
Connect the connector.
| 19. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH |
![]() |
Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.
![]() |
Install the door glass to the window regulator with the 2 bolts.
| 20. INSTALL FRONT DOOR SERVICE HOLE COVER LH |
Install the front door service hole cover to the door panel.
Connect the connector.
| 21. INSTALL FRONT NO. 1 DOOR TRIM BRACKET |
![]() |
Install the bracket with the 2 screws.
| 22. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Connect the connector.
Install the front No. 1 speaker assembly with the 4 screws.
| 23. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH |
![]() |
Temporarily install the outer rear view mirror assembly by inserting the claw on the outer rear view mirror assembly into the holes on the vehicle.
Tighten the 3 nuts in the sequence shown in the illustration to install the outer rear view mirror assembly.
w/ Power Mirror Control System:
Connect the connector labeled A.
| 24. INSTALL OUTER MIRROR CONTROL ECU |
![]() |
Install the ECU with the 2 screws.
Connect the 2 ECU connectors.
| 25. INSTALL SEAT MEMORY SWITCH (w/ Seat Memory Switch) |
![]() |
Install the seat memory with the 2 screws.
| 26. INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH |
| 27. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH |
![]() |
Connect the 2 cables to the inside handle.
Connect the connector.
Attach the inside handle's knob to the door trim board.
![]() |
Attach the 9 clips to install the door trim board.
Install the inside handle and door trim board to the door trim panel with the screw.
Install the door trim board to the door panel with the screw.
Install the clip.
| 28. INSTALL FRONT DOOR ARMREST COVER LH |
| 29. INSTALL FRONT NO. 3 SPEAKER ASSEMBLY |
![]() |
Attach the 3 claws to install the front No. 3 speaker assembly to the bracket.
![]() |
Install the front No. 3 speaker assembly with the bracket to the front lower door frame bracket garnish LH with the 3 screws.
| 30. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH |
![]() |
Attach the 3 clips to install the front lower door frame bracket garnish.
| 31. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
![]() |
Install the power window regulator master switch assembly with the 3 screws.
| *A | for Regular Cab |
| *B | for Double Cab, for CrewMax |
| 32. INSTALL FRONT UPPER ARMREST BASE PANEL LH |
Connect the master switch connector.
![]() |
Attach the 2 clips and 5 claws to install the front upper armrest base panel LH.
| 33. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH |
![]() |
Attach the 4 claws to install the bezel plug.
| 34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 35. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).