LIGHTING SYSTEM > Turn Signal Light Circuit |

| 1.CHECK TURN SIGNAL LIGHT |
Check that the turn signal lights blink.
| Result | Proceed to |
| All turn signal lights do not blink | A |
| Only front turn signal light does not blink | B |
| Only rear combination light does not blink | C |
| Only door mirror foot light does not blink | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT FUSE (LH-IG, TURN-HAZ) |
Remove the LH-IG fuse from the main body ECU.
Remove the TURN-HAZ fuse from the engine room junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| LH-IG fuse | Always | Below 1 Ω |
| TURN-HAZ fuse |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER - BATTERY AND BODY GROUND) |
![]() |
Disconnect the J29 relay connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J29-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch OFF | Below 1 V | |
| J29-1 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J29-4 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - TURN SIGNAL FLASHER AND BODY GROUND) |
![]() ![]() |
for LH:
Disconnect the A12 light connector.
Disconnect the J29 relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A12-3 (B) - J29-10 (TRNL) | Always | Below 1 Ω |
| A12-2 (E) - Body ground | ||
| A12-3 (B) - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the A13 light connector.
Disconnect the J29 relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A13-3 (B) - J29-17 (TRNR) | Always | Below 1 Ω |
| A13-2 (E) - Body ground | ||
| A13-3 (B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL FLASHER AND BODY GROUND) |
![]() ![]() |
for LH:
Disconnect the R13 light connector.
Disconnect the J29 relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R13-1 (TRN) - J29-2 (LL) | Always | Below 1 Ω |
| R13-2 (E) - Body ground | ||
| R13-1 (TRN) - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the R14 light connector.
Disconnect the J29 relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R14-1 (TRN) - J29-8 (LR) | Always | Below 1 Ω |
| R14-2 (GND) - Body ground | ||
| R14-1 (TRN) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER AND BODY GROUND) |
![]() ![]() |
for LH:
Disconnect the N5 light connector.
Disconnect the J29 relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N5-4 (TRNL) - J29-2 (LL) | Always | Below 1 Ω |
| N5-3 (GND) - Body ground | ||
| N5-4 (TRNL) - Body ground | Always | 10 kΩ or higher |
for RH:
Disconnect the M6 light connector.
Disconnect the J29 relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M6-4 (TRNR) - J29-8 (LR) | Always | Below 1 Ω |
| M6-3 (GND) - Body ground | ||
| M6-4 (TRNR) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||