Home › STEERING › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt)

STEERING COLUMN ASSEMBLY (for Manual Tilt) > INSTALLATION

for Preparation Click here



1. INSTALL STEERING COLUMN ASSEMBLY


    C290070
  1. Install the steering column with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C155151E02
  1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.
    Text in Illustration 
    *a
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    C155150E02
  1. Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C154524E02
  1. Align the matchmarks on the steering column and steering intermediate shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C155149
  1. Install the 3 bolts and nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    C154523
  1. Install the air duct with the bolt.



5. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    B225998
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 2 claws to install the DLC3.

  1. Install the 4 bolts to install the instrument panel airbag.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH


  1. Connect the hood lock control cable to the hood lock control lever, rotate the hood lock control cable, and then slide and push the hood lock control cable into place.


    B355340

  1. Attach the 3 hooks to connect the hood lock control lever to the lower instrument panel finish panel sub-assembly LH.

  1. Connect each connector.



    B355338
  1. Attach the 9 clips and 2 claws to install the lower instrument panel finish panel sub-assembly LH.

  1. Install the 2 bolts <A>.



7. INSTALL INSTRUMENT SIDE PANEL LH


    B355334
  1. Attach the 4 guides and 3 claws to install the instrument side panel LH.



8. INSTALL COWL SIDE TRIM BOARD LH
  1. Attach the 2 clips to install the cowl side trim board LH.

  1. Install the nut.



9. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)

HINT:
Use the same procedure described for the LH side.



10. INSTALL FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax)

HINT:
Use the same procedure described for the LH side.



11. INSTALL COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY


C155886
  1. Using a T30 ''TORX'' wrench, install the column shift with the 3 bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the connector and attach the harness clamp.



    C158379E01
  1. Connect the column shift transmission control cable end to the column shift.

    NOTICE:
    Make sure to install the cable end so that the inner cable is not twisted. Confirm that the cable end's ridged side is facing upward.



12. CONNECT COLUMN SHIFT TRANSMISSION CONTROL CABLE ASSEMBLY


C157286
  1. Insert the column shift transmission control cable from the vehicle interior, and install the cable retainer with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    C158378
  1. Connect the cable to the steering column shaft bracket so that the outer cable socket's claws attach securely.



    C158379E01
  1. Connect the column shift transmission control cable end to the column shift.

    NOTICE:
    Make sure to install the cable end so that the inner cable is not twisted. Confirm that the cable end's ridged side is facing upward.



    C157289
  1. Connect the 2 cable clamps with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Return the floor carpet front LH side to its original position.

  1. Move the shift lever to the N position.



    C155873E01
  1. Turn the control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.



    C158380E01
  1. Connect the control cable with a new clip and the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the inside of the vehicle.



    C157285
  1. Connect the transmission control cable support with the nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



13. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C290069
  1. Install the turn signal switch with spiral cable to the steering column with the clamp.



    C154522
  1. Connect the 5 connectors to the turn signal switch with spiral cable.



14. INSTALL UPPER STEERING COLUMN COVER


    C290068
  1. Attach the claw to install the upper steering column cover.

  1. Attach the 4 clips.



15. INSTALL LOWER STEERING COLUMN COVER


    C290067
  1. Attach the 2 claws to install the lower steering column cover.

  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



16. ADJUST SPIRAL CABLE


    B166449
  1. Check that the ignition switch is OFF.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Rotate the spiral cable sub-assembly with steering sensor counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable sub-assembly with steering sensor by the airbag wire harness.



    B166450
  1. Rotate the spiral cable sub-assembly with steering sensor clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable sub-assembly with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable sub-assembly with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.



17. INSTALL STEERING WHEEL ASSEMBLY


    C290071E01
  1. Align the matchmarks on the steering wheel and steering main shaft.
    Text in Illustration 
    *a
    Matchmark

  1. Install the steering wheel set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



18. INSPECT STEERING WHEEL CENTER POINT


19. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Support the steering pad with one hand.



    B354950
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.

  1. Push in the 2 airbag connector locks to install the 2 airbag connectors.

  1. Connect the horn connector to the steering pad.

  1. Install the steering pad.



    B360541
  1. Using T30 "TORX" socked wrench, tighten the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



20. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    B355450
  1. Attach the guide and claw to install the lower No. 3 steering wheel cover.



21. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    B355451
  1. w/ Cruise Control:

    1. Attach the guide and claw to install the lower No. 2 steering wheel cover.



    B356801
  1. w/o Cruise Control:

    1. Attach the guide and claw to install the lower No. 2 steering wheel cover.



22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



23. CHECK SRS WARNING LIGHT
(Click here)