STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) > REMOVAL |
| 1. PRECAUTION |
| 2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE LOWER NO. 3 STEERING WHEEL COVER |
![]() |
Using a screwdriver, detach the claw and guide and remove the lower No. 3 steering wheel cover.
| *1 | Protective Tape |
| 5. REMOVE LOWER NO. 2 STEERING WHEEL COVER |
![]() |
w/ Cruise Control:
| *1 | Protective Tape |
Using a screwdriver, detach the claw and guide and remove the lower No. 2 steering wheel cover.
![]() |
w/o Cruise Control:
| *1 | Protective Tape |
Using a screwdriver, detach the claw and guide and remove the lower No. 2 steering wheel cover.
| 6. REMOVE STEERING PAD |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.
Pull the steering pad toward you.
![]() |
Disconnect the horn connector from the steering pad.
Using a screwdriver, release the 2 airbag connector locks.
| *1 | Protective Tape |
Disconnect the 2 airbag connectors and remove the steering pad as shown in the illustration.
| 7. REMOVE STEERING WHEEL ASSEMBLY |
Remove the steering wheel set nut.
![]() |
Put matchmarks on the steering wheel and main shaft.
| *a | Matchmark |
| *b | Hold |
| *c | Turn |
Using SST, remove the steering wheel.
| 8. REMOVE LOWER STEERING COLUMN COVER |
![]() |
Remove the 2 screws.
Detach the 2 claws to remove the lower steering column cover.
| 9. REMOVE UPPER STEERING COLUMN COVER |
![]() |
Detach the 4 clips.
Detach the claw to remove the upper steering column cover.
| 10. REMOVE TILT AND TELESCOPIC MANUAL SWITCH |
![]() |
Disconnect the connector.
Using a screwdriver, detach the claw and pull out the tilt and telescopic switch.
| 11. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Disconnect the 5 connectors from the combination switch with spiral cable.
![]() |
Using pliers, grip the claws of the clamp and remove the combination switch with spiral cable from the steering column.
| 12. REMOVE FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Detach the 6 claws and 3 clips, and remove the front door scuff plate LH.
| 13. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab, CrewMax) |
![]() |
Detach the 6 claws and 3 clips, and remove the front door scuff plate LH.
| 14. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the nut.
Detach the 2 clips and remove the cowl side trim board LH.
| 15. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover B, detach the 3 claws, 4 guides and remove the instrument side panel LH.
| 16. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH |
Operate the tilt lever to fully extend and raise the steering column.
![]() |
Apply protective tape as shown in the illustration.
| *1 | Protective Tape |
Remove the 2 bolts <A>.
Detach the 9 clips, 2 claws and remove the lower instrument panel finish panel sub-assembly LH.
Disconnect each connector.
![]() |
Detach the 3 hooks and disconnect the hood lock control lever from the lower instrument panel finish panel sub-assembly LH.
Pull and slide the hood lock control cable, rotate the hood lock control cable, and then disconnect the hood lock control cable from the hood lock control lever.

| 17. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
![]() |
Remove the 4 bolts and remove the instrument panel airbag.
Detach the 2 claws and disconnect the DLC3.
Disconnect the connector.
| 18. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY |
![]() |
Remove the bolt and air duct.
| 19. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY |
![]() |
Remove the 3 bolts and nut.
![]() |
Put matchmarks on the steering intermediate shaft and the steering column.
| *a | Matchmark |
Remove the bolt and steering intermediate shaft from the steering column.
![]() |
Put matchmarks on the No. 2 steering intermediate shaft and steering intermediate shaft.
| *a | Matchmark |
Remove the bolt and steering intermediate shaft from the No. 2 steering intermediate shaft.
| 20. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Put matchmarks on the No. 2 steering intermediate shaft and power steering gear.
| *a | Matchmark |
Remove the bolt and No. 2 steering intermediate shaft from the power steering gear.
| 21. REMOVE STEERING COLUMN ASSEMBLY |
![]() |
Remove the bolt and 2 nuts. Then remove the steering column from the instrument panel reinforcement.