Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)

POWER WINDOW REGULATOR MOTOR (for Front Door) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the LH side and RH side.
  2. The procedure listed below is for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


E281627
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 ''TORX'' driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    For a new front window regulator, the installation position of the regulator will be set when the self-tapping screws are installed.



2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
  1. for Regular Cab:
    Install the front door window regulator sub-assembly LH .

  1. for Double Cab:
    Install the front door window regulator sub-assembly LH .

  1. for CrewMax:
    Install the front door window regulator sub-assembly LH .



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. for Regular Cab:
    Install the front door glass sub-assembly LH .

  1. for Double Cab:
    Install the front door glass sub-assembly LH .

  1. for CrewMax:
    Install the front door glass sub-assembly LH .



4. INSTALL FRONT DOOR SERVICE HOLE COVER LH
  1. for Regular Cab:
    Install the front door service hole cover LH .

  1. for Double Cab:
    Install the front door service hole cover LH .

  1. for CrewMax:
    Install the front door service hole cover LH .



5. INSTALL FRONT NO. 1 DOOR TRIM BRACKET
  1. for Regular Cab:
    Install the front No. 1 door trim bracket .

  1. for Double Cab:
    Install the front No. 1 door trim bracket .

  1. for CrewMax:
    Install the front No. 1 door trim bracket .



6. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
  1. for Regular Cab:
    Install the front No. 1 speaker assembly .

  1. for Double Cab:
    Install the front No. 1 speaker assembly .

  1. for CrewMax:
    Install the front No. 1 speaker assembly .



7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
  1. for Regular Cab:
    Install the front door trim board sub-assembly LH .

  1. for Double Cab:
    Install the front door trim board sub-assembly LH .

  1. for CrewMax:
    Install the front door trim board sub-assembly LH .



8. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH
  1. for Regular Cab:
    Install the front lower door frame bracket garnish LH .

  1. for Double Cab:
    Install the front lower door frame bracket garnish LH .

  1. for CrewMax:
    Install the front lower door frame bracket garnish LH .



9. INSTALL FRONT UPPER ARMREST BASE PANEL LH
  1. Connect the master switch connector.



    E278373E01
  1. Attach the 2 clips and 5 claws to install the front upper armrest base panel LH.
    Text in Illustration 
    *A
    for Regular Cab
    *B
    for Double Cab, for CrewMax



10. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH
  1. for Regular Cab:
    Install the front door inside handle bezel plug LH .

  1. for Double Cab:
    Install the front door inside handle bezel plug LH .

  1. for CrewMax:
    Install the front door inside handle bezel plug LH .



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).