Home › ENGINE ยท 3UR-FBE › EMISSION CONTROL › AIR SWITCHING VALVE

AIR SWITCHING VALVE > INSTALLATION

for Preparation Click here



1. INSTALL NO. 3 AIR TUBE


    A158585E03
  1. Install a new gasket and the No. 3 air tube with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    Identification Color

    NOTICE:
    Make sure the gasket's claws are not caught between the air tube and air switching valve.

    HINT:
    The identification color on the flange is orange.



2. INSTALL NO. 2 AIR TUBE


    A158584E03
  1. Install a new gasket and the No. 2 air tube with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    Identification Color

    NOTICE:
    Make sure the gasket's claws are not caught between the air tube and air switching valve.

    HINT:
    The identification color on the flange is blue.



3. INSTALL AIR SWITCHING VALVE ASSEMBLY
  1. Install the air switching valve assembly with the 3 bolts to the No. 1 heat exchanger cover.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 air switching valve assembly connectors.

  1. Install the bracket to the air switching valve assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the knock sensor connector.



4. INSTALL AIR TUBE
  1. Connect the 2 No. 1 air hoses to the air tube.

  1. Connect the air tube to the air switching valve assembly, and install the air tube with the 2 bolts to the No. 1 heat exchanger cover.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A158575E06
  1. Connect the air pump connector clamp holder.
    Text in Illustration 
    *1
    No. 2 Air Hose
    *2
    No. 3 Air Hose

  1. Attach the wire harness claw.

  1. Connect the air pump connector.

  1. Connect the No. 2 air hose and No. 3 air hose, and slide the 2 clamps to secure the hoses.



5. INSTALL NO. 3 WATER BY-PASS PIPE

HINT:
Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.



    A307664E01
  1. Install the No. 3 water by-pass pipe to the front water by-pass joint with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *a
    Stopper
    *b
    Protrusion

    NOTICE:
    Align the notch of the stopper with the protrusion of the front water by-pass joint.



6. INSTALL FRONT WATER BY-PASS JOINT
  1. Install 2 new gaskets and the front water by-pass joint with the 4 nuts to the cylinder head.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the engine coolant temperature sensor connector.



7. CONNECT NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Connect the No. 2 water by-pass pipe sub-assembly with the 3 bolts to the timing chain cover and front water by-pass joint.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



8. CONNECT NO. 2 WATER BY-PASS HOSE
  1. Connect the No. 2 water by-pass hose to the water by-pass joint, and slide the clamp to secure the hose.



9. INSTALL NO. 1 WATER BY-PASS HOSE
  1. Install the No. 1 water by-pass hose to the front water by-pass joint and water inlet housing, and slide the clamp to secure the hose.



10. INSTALL NO. 10 WATER BY-PASS HOSE


    A307663E03
  1. Install the No. 10 water by-pass hose to the separator case and front water by-pass joint, and slide the 2 clamps to secure the hoses.
    Text in Illustration 
    *1
    No. 9 Water By-pass Hose
    *2
    No. 10 Water By-pass Hose
    *a
    Paint Mark (Pink)
    *b
    Paint Mark (White)

    HINT:
    Make sure that the color on the hose matches with the color on the separator case.



11. INSTALL NO. 9 WATER BY-PASS HOSE
  1. Install the No. 9 water by-pass hose to the separator case and front water by-pass joint, and slide the 2 clamps to secure the hoses.

    HINT:
    Make sure that the color on the hose matches with the color on the separator case.



12. INSTALL NO. 1 ENGINE COVER


A158656

NOTICE:
Make sure that the No. 1 engine cover is level with the top surface of the intake port of the cylinder head for 1 and 2.

HINT:
  1. Align the No. 1 engine cover cutouts with the air tube.
  2. Align the No. 1 engine cover with the air switching valve surface and cylinder head wall.



13. CONNECT FUEL TUBE CLAMP
  1. Connect the fuel tube clamp to the bracket.



14. INSTALL NO. 2 ENGINE COVER


A307709

NOTICE:
Make sure that the No. 2 engine cover is level with the top surface of the intake port if the cylinder head.

HINT:
  1. Align the No. 2 engine cover cutout with the air tube.
  2. Align the No. 2 engine cover with the front water by-pass joint and cylinder head wall.



15. INSTALL FAN SHROUD
(Click here)


16. INSTALL INTAKE MANIFOLD
(Click here)


17. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY
(Click here)