Home › ENGINE ยท 1UR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSTALLATION

for Preparation Click here



1. INSTALL NOISE FILTER
  1. RH Side:
    Install the noise filter to the cylinder head cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. LH Side:
    Install the noise filter to the cylinder head cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



2. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 8 ignition coils with the 8 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



3. INSTALL KNOCK SENSOR

HINT:
Perform "Inspection After Repairs" after replacing the knock sensor (Click here).



    A215437E03
  1. Install the 4 knock sensors with the 4 bolts so that the sensors are angled as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    Text in Illustration 
    *a
    Bank 2 Sensor 1
    *b
    Bank 1 Sensor 1
    *c
    Bank 2 Sensor 2
    *d
    Bank 1 Sensor 2
    *e
    Front
    *f
    Upper
    *g
    Rear

    NOTICE:
    The acceptable installation angle of the knock sensor is between 10° upward and 2° downward from the horizontal position.

  1. Connect the 4 knock sensor connectors.



4. INSTALL NO. 11 WATER BY-PASS HOSE


    A214840E01
  1. Install the No. 11 water by-pass hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.



5. INSTALL ENGINE WIRE


A214595
  1. Connect the 3 clamps and 4 knock sensor connectors to install the engine wire.



6. INSTALL NO. 1 ENGINE COVER


    A308822
  1. Install the No. 1 engine cover.



7. INSTALL NO. 2 ENGINE COVER


    A214852
  1. Install the No. 2 engine cover.



8. INSTALL SEPARATOR CASE
  1. Install the separator case with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
  1. Install the No. 1 idler pulley sub-assembly to the timing chain cover sub-assembly with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



10. INSTALL WATER PUMP PULLEY
  1. Temporarily install the water pump pulley with the 4 bolts.



    A210018E02
  1. Using SST, hold the water pump pulley and tighten the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



11. INSTALL FRONT WATER BY-PASS JOINT
  1. Install 2 new gaskets and the front water by-pass joint to the cylinder head with the 4 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the No. 2 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.



12. INSTALL WATER INLET HOUSING


    A162555E05
  1. Install a new gasket to the timing chain cover sub-assembly.
    Text in Illustration 
    *1
    Gasket

  1. Install the water inlet housing with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



13. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Connect the No. 2 water by-pass hose to the water by-pass pipe sub-assembly, and slide the clamp to secure the hose.

  1. Install the water by-pass pipe sub-assembly to the cylinder head cover sub-assembly RH with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



14. INSTALL AIR TUBE SUB-ASSEMBLY RH
  1. Install the air tube sub-assembly RH to the cylinder head cover sub-assembly RH with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



15. INSTALL NO. 1 WATER BY-PASS HOSE


    A215866E01
  1. Install the No. 1 water by-pass hose.

    HINT:
    The direction of hose clamp is indicated in the illustration.



16. INSTALL NO. 3 ENGINE COVER


    A309475
  1. Install the No. 3 engine cover.



17. INSTALL NO. 4 ENGINE COVER


    A214270
  1. Install the No. 4 engine cover.



18. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY


    A118764E02
  1. Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    A162467
  1. Install the oil pressure sender gauge.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.



    A163657
  1. Connect the sender gauge connector.



19. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH


    A214315
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head sub-assembly RH.

  1. Install the fuel delivery pipe sub-assembly RH (with injectors) to the cylinder head sub-assembly RH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    NOTICE:
    A163659E09
    Make sure that the part of the fuel injector labeled B is between the parts of the fuel delivery pipe labeled A.

  1. Connect the No. 6 wire harness connector.



20. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH


    A214316
  1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head sub-assembly LH.

  1. Install the fuel delivery pipe sub-assembly LH (with injectors) to the cylinder head sub-assembly LH.



  1. Install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    NOTICE:
    A163659E08
    Make sure that the part of the fuel injector labeled B is between the parts of the fuel delivery pipe labeled A.

  1. Connect the No. 7 wire harness connector.



21. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH


A214594
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



22. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH


A214593
  1. Install the mounting bracket with the 4 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



23. INSTALL FRONT ENGINE MOUNTING INSULATOR RH


    A214807
  1. Install the mounting insulator with the nut.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }



24. INSTALL FRONT ENGINE MOUNTING INSULATOR LH


    A214808
  1. Install the mounting insulator with the nut.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }



25. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


A076531E01
  1. Apply adhesive to 2 or 3 threads of the drain cocks.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    A163841E01
  1. Install the water drain cocks.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Tighten the drain cocks up to an additional 360° so that the drain cock pipes are within the range shown in the illustration.

    NOTICE:
    1. Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks to the specified torque.
    2. Do not loosen the drain cocks to adjust them. If an adjustment is necessary, remove the drain cocks and reinstall them.

  1. Install the water drain cock plugs to the water drain cocks.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



26. INSTALL EGR COOLER ASSEMBLY


    A214295
  1. Install the EGR cooler with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



27. CONNECT NO. 11 WATER BY-PASS HOSE


    A214832E01
  1. Connect the No. 11 water by-pass hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.



28. INSTALL NO. 8 WATER BY-PASS HOSE


    A308823E01
  1. Install the No. 8 water by-pass hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.



29. INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY


    A214865E01
  1. Install the No. 3 water by-pass pipe with the 2 bolts and connect the hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



30. INSTALL NO. 3 AIR TUBE


    A214893
  1. Install the No. 3 air tube with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A214881
  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



31. INSTALL NO. 4 AIR TUBE


    A214892
  1. Install the No. 4 air tube with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A214880
  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



32. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 2)


    A308824E01
  1. Install a new gasket and the air switching valve assembly with the 3 bolts.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Make sure the gasket's claws are not caught between the air switching valve assembly and No. 3 air tube.



    A308819
  1. Install the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



33. INSTALL AIR SWITCHING VALVE ASSEMBLY (for Bank 1)


    A308825E01
  1. Install a new gasket and the air switching valve assembly with the 3 bolts.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Make sure the gasket's claws are not caught between the air switching valve assembly and No. 4 air tube.



    A308817
  1. Install the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



34. INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY


    A214592E02
  1. Install the No. 2 fuel tube (Click here).



35. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
  1. Install the No. 1 fuel pipe (Click here).



36. INSTALL ENGINE WIRE


A214589E01
  1. Engine Rear Side:

    1. Install the 4 bolts.

      Torque:
      8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

    2. Connect the clamp and connector.



    A308816
  1. Engine RH Side:

    1. Connect the 6 clamps.

    2. Connect the oil pressure sender gauge connector.

    3. Connect the air switching valve connector.

    4. Connect the noise filter connector.

    5. Connect the fuel injector connector.

    6. Connect the 2 VVT sensor connectors.

    7. Connect the 4 ignition coil connectors.

    8. Connect the 2 camshaft timing control valve connectors.



    A308815
  1. Engine LH Side:

    1. Connect the 8 clamps and install the engine wire with the bolt.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    2. Connect the noise filter connector.

    3. Connect the fuel injector connector.

    4. Connect the engine coolant temperature sensor connector.

    5. Connect the air switching valve connector.

    6. Connect the crankshaft position sensor connector.

    7. Connect the camshaft position sensor connector.

    8. Connect the 2 VVT sensor connectors.

    9. Connect the 4 ignition coil connectors.

    10. Connect the 2 camshaft timing control valve connectors.