Home › ENGINE ยท 3UR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > REMOVAL

for Preparation Click here



1. REMOVE ENGINE WIRE


A259653
  1. Engine LH Side:

    1. Disconnect the 2 camshaft timing control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the 2 VVT sensor connectors.

    4. Disconnect the camshaft position sensor connector.

    5. Disconnect the vacuum switching valve connector (for ACIS).

    6. Disconnect the purge VSV connector.

    7. Disconnect the engine coolant temperature sensor connector.

    8. Disconnect the fuel injector connector.

    9. Remove the bolt and disconnect the 8 clamps.



    A259650
  1. Engine RH Side:

    1. Disconnect the 2 camshaft timing control valve connectors.

    2. Disconnect the 4 ignition coil connectors.

    3. Disconnect the 2 VVT sensor connectors.

    4. Disconnect the fuel injector connector.

    5. Disconnect the throttle sensor connector.

    6. Disconnect the oil pressure sender gauge connector.

    7. Disconnect the 9 clamps.



    A259651
  1. Engine Rear Side:

    1. Disconnect the 3 connectors.

    2. Disconnect the 5 clamps.

    3. Remove the 3 bolts and disconnect the 3 wires.

  1. Remove the engine wire.



2. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY


A308965
  1. Remove the No. 1 fuel pipe (Click here).



3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


A163838E01
  1. Remove the 2 water drain cock plugs from the water drain cocks.

  1. Remove the 2 water drain cocks from the cylinder block.



4. REMOVE FRONT ENGINE MOUNTING INSULATOR RH


    A163786
  1. Remove the nut and mounting insulator.



5. REMOVE FRONT ENGINE MOUNTING INSULATOR LH


    A163787
  1. Remove the nut and mounting insulator.



6. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


A160649
  1. Remove the 4 bolts and mounting bracket.



7. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH


A160648
  1. Remove the 4 bolts and mounting bracket.



8. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH
  1. Disconnect the No. 7 wire harness connector.

  1. Remove the No. 1 engine cover.



    A256331
  1. Remove the 2 bolts and fuel delivery pipe LH.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head LH.



9. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH


    A161422
  1. Disconnect the ventilation hose and No. 6 wire harness connector.

  1. Remove the No. 3 engine cover.



    A256330
  1. Remove the 2 bolts and fuel delivery pipe RH.

    NOTICE:
    When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.

  1. Remove the 2 delivery pipe spacers and 4 insulators from the cylinder head RH.



10. DISCONNECT VENTILATION HOSE ASSEMBLY


    A162091E01
  1. Slide the 2 clamps and disconnect the ventilation hose assembly from the ventilation pipe of the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.



11. REMOVE NO. 1 TUBE


A163943
  1. Remove the 2 bolts and No. 1 tube.



12. REMOVE INTAKE MANIFOLD


    A162089
  1. Remove the No. 1 engine cover sub-assembly.



    A162090
  1. Remove the No. 3 engine cover.

  1. Disconnect the throttle body connector from the throttle body assembly.



    A307759
  1. Slide the 2 clamps and disconnect the 2 water by-pass hoses from the inlet water housing and front water by-pass joint.



    A162103
  1. Slide the clamp and disconnect the ventilation hose from the intake manifold.



    A162082
  1. Disconnect the 2 vacuum switching valve connectors.

  1. Slide the clamp and disconnect the purge line hose from the purge VSV.



    A165518
  1. Remove the 2 bolts to disconnect the No. 1 tube.

  1. Slide the clamp and disconnect the union to connector tube hose from the No. 1 tube.



    A165471
  1. Detach the 3 wire harness clamps from the 3 wire harness clamp brackets.



    A165472
  1. Remove the bolt and wire harness clamp bracket from the intake manifold.



    A165478
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



13. REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY


    A256359
  1. Remove the 2 bolts and No. 2 fuel tube.



14. REMOVE FUEL TUBE SUB-ASSEMBLY


A256360


15. REMOVE NO. 2 WATER BY-PASS PIPE


    A165547
  1. Slide the 4 clamps and disconnect the 4 hoses from the No. 2 water by-pass pipe.

  1. Remove the 3 bolts and No. 2 water by-pass pipe.



16. REMOVE NO. 1 WATER BY-PASS HOSE


    A308519
  1. Slide the 2 clamps and remove the No. 1 water by-pass hose from the water inlet housing and front water by-pass joint.



17. REMOVE FRONT WATER BY-PASS JOINT


    A291566
  1. Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.

  1. Remove the 4 nuts, front water by-pass joint and 2 gaskets.



18. REMOVE NO. 2 ENGINE COVER


A307666


19. REMOVE NO. 1 ENGINE COVER


A158581


20. REMOVE WATER PUMP PULLEY


    A151837E01
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-01000)

  1. Remove the 4 bolts and water pump pulley.



21. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY


    A162557
  1. Remove the bolt and No. 1 idler pulley sub-assembly.



22. REMOVE FAN BRACKET SUB-ASSEMBLY


    A162558
  1. Remove the 4 bolts and fan bracket assembly.



23. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A162527
  1. Remove the standard bolt, 6 mm hexagon wrench bolt and V-ribbed belt tensioner assembly.



24. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY


    A163657
  1. Disconnect the sender gauge connector.



    A162467
  1. Remove the oil pressure sender gauge.



25. REMOVE AIR TUBE


    A162553
  1. Remove the bolt, disconnect the 2 hoses, and remove the air tube sub-assembly.



26. REMOVE WATER INLET HOUSING


    A162554
  1. Remove the 3 bolts, water inlet housing and gasket.



27. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY


    A162550
  1. Remove the bolt and disconnect the air tube sub-assembly.



    A162551
  1. Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.

  1. Remove the 2 bolts and water by-pass pipe sub-assembly.



28. REMOVE AIR SWITCHING VALVE ASSEMBLY


    A158583
  1. Disconnect the knock sensor connector.

  1. Remove the bolt and bracket.

  1. Disconnect the 2 air switching valve assembly connectors.



    A158586
  1. Remove the 3 bolts and air switching valve assembly.



29. REMOVE NO. 2 AIR TUBE


    A158584
  1. Remove the 2 bolts, No. 2 air tube and gasket.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



30. REMOVE NO. 3 AIR TUBE


    A158585
  1. Remove the 2 bolts, No. 3 air tube and gasket.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.



31. REMOVE ENGINE WIRE


A306987
  1. Disconnect the 4 knock sensor connectors.

  1. Disconnect the 3 clamps. Then remove the engine wire.



32. REMOVE SEPARATOR CASE


    A271506
  1. Remove the 4 bolts and separator case.



33. REMOVE KNOCK SENSOR
  1. Disconnect the 4 knock sensor connectors.



    A158615
  1. Remove the 4 bolts and 4 knock sensors.



34. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 8 bolts and 8 ignition coils.