Home › ENGINE · 3UR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE OIL FILTER ELEMENT


    A094910E01
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.



    A162459
  1. Remove the oil filter drain plug.



    A162460
  1. Install the pipe to the oil filter cap.

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A162461
  1. Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.



    A162462E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



    A162463
  1. Remove the oil filter element and O-ring from the oil filter cap.

    NOTICE:
    Be sure to remove the O-ring for the cap by hand, without using any tools, to prevent damage to the cap's O-ring groove.



2. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)


    A163672
  1. Remove the 2 nuts and bracket.

  1. Disconnect the ground wire from the cylinder block.



3. REMOVE OIL FILTER BRACKET (w/ Oil Cooler)


    A162469
  1. Remove the 2 bolts, 2 nuts and filter bracket.



    A162470
  1. Remove the 2 O-rings.



4. REMOVE OIL FILTER BRACKET (w/o Oil Cooler)


    A163541
  1. Remove the 2 bolts, 2 nuts and oil filter bracket.



    A162470
  1. Remove the 2 O-rings.



5. REMOVE CRANKSHAFT PULLEY


    A164228E05
  1. Using SST, loosen the crankshaft pulley set bolt.
    Text in Illustration 
    *a
    SST
    *b
    Turn
    *c
    Hold

    SST
    09213-70011  
    09330-00021  

  1. Partially install the crankshaft pulley set bolt to the crankshaft pulley until 2 or 3 threads are engaged.



    A164229E04
  1. Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley.
    Text in Illustration 
    *a
    SST
    *b
    Turn
    *c
    Hold

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05011)



6. REMOVE OIL FILLER CAP SUB-ASSEMBLY


7. REMOVE OIL FILLER CAP HOUSING


    A161903
  1. Remove the 2 bolts, filler cap housing and gasket.



8. REMOVE SPARK PLUG


9. REMOVE VVT SENSOR


    A161904
  1. LH:
    Remove the 2 bolts and 2 VVT sensors.



    A161905
  1. RH:
    Remove the 2 bolts and 2 VVT sensors.



10. REMOVE CAMSHAFT POSITION SENSOR


    A161906
  1. Remove the bolt and camshaft position sensor.



11. REMOVE CRANK POSITION SENSOR PROTECTOR


A161907
  1. Remove the 2 bolts and sensor protector.



12. REMOVE CRANKSHAFT POSITION SENSOR


    A161908
  1. Remove the bolt and crankshaft position sensor.



13. REMOVE CAMSHAFT OIL CONTROL VALVE ASSEMBLY


    A161909
  1. LH:
    Remove the 2 bolts and 2 oil control valves.



    A161910
  1. RH:
    Remove the 2 bolts and 2 oil control valves.



14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A162523
  1. Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A162524
  1. Remove the 5 gaskets from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.



15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH


    A162525
  1. Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A162526
  1. Remove the 5 gaskets from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.



16. REMOVE OIL CONTROL VALVE FILTER


A164313E01
  1. LH:
    Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.



    A164314E01
  1. RH:
    Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.



17. REMOVE SPARK PLUG TUBE GASKET


A164315E01
  1. Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.

  1. Using a screwdriver, pry out the gaskets.

    NOTICE:
    Be careful not to damage the cylinder head cover.

    HINT:
    1. Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.
    2. Tape the screwdriver tip before use.



18. REMOVE WATER PUMP ASSEMBLY


    A151828
  1. Remove the 8 bolts, water pump and gasket.



19. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A162529E02
  1. Remove the 28 bolts and nut shown in the illustration.
    Text in Illustration 
    *1
    Nut



    A162530
  1. Remove the timing chain cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

    NOTICE:
    Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain cover sub-assembly.

    HINT:
    Tape the screwdriver tip before use.



    A162531
  1. Remove the oil pump gasket from the cylinder block.



    A164415
  1. Remove the O-ring from the oil pan sub-assembly.



20. REMOVE WATER INLET PIPE


    A162532
  1. Remove the water inlet pipe from the No. 1 heat exchanger cover.

  1. Remove the 2 O-rings from the water inlet pipe.



21. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Place the timing chain cover on wooden blocks.



    A163996E01
  1. Place the oil pump on a wooden block.

  1. Using a screwdriver and wooden block, pry out the oil seal.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.



22. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily tighten the pulley set bolt.



  1. Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

    HINT:
    If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



    A160654E01



23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH


A160732E01
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.



    A160733
  1. Remove the 2 bolts, chain tensioner and gasket.



24. REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH


A178535


25. REMOVE NO. 1 CHAIN VIBRATION DAMPER LH


A178536
  1. Remove the 2 bolts and chain vibration damper.



26. REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH


A160655E01
  1. While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.



    A160656E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.



    A160657E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    Be careful not to damage the cylinder head with the wrench.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.

  1. Remove the No. 1 and No. 2 chains from the gears.



27. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


A148225E01
  1. Remove the 2 bolts and chain tensioner.



28. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH


A150062E01
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.



    A150146
  1. Remove the 2 bolts and chain tensioner.



29. REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH


A178486


30. REMOVE NO. 1 CHAIN VIBRATION DAMPER RH


A160658
  1. Remove the 2 bolts and vibration damper.



31. REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH


A160659E01
  1. While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.



    A160660E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    1. Be careful not to damage the cylinder head with the wrench.
    2. Do not disassemble the camshaft timing gear.



    A160661E01
  1. Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

    NOTICE:
    Be careful not to damage the cylinder head with the wrench.

  1. Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.

  1. Remove the No. 1 and No. 2 chains from the gears.



32. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


A148224E01
  1. Remove the 2 bolts and chain tensioner.



33. REMOVE CRANKSHAFT TIMING GEAR KEY


A145630
  1. Using a screwdriver, remove the 2 timing gear keys from the crankshaft.



34. REMOVE CAMSHAFT BEARING CAP LH


A163591E01
  1. Make sure that the knock pin of the camshaft is positioned as shown in the illustration.



    A163592E02
  1. Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.



    A163593E02
  1. Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the No. 3 and No. 4 camshafts.



35. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


    A163594
  1. Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.



36. REMOVE CAMSHAFT BEARING CAP RH


A160683E01
  1. Make sure that the knock pin of the camshaft is positioned as shown in the illustration.



    A160684E02
  1. Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.



    A160685E01
  1. Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 6 bearing caps.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the No. 1 and No. 2 camshafts.



37. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


A160735
  1. Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

    HINT:
    Tape the screwdriver tip before use.



38. REMOVE VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 32 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



39. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 32 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



40. REMOVE VALVE STEM CAP
  1. Remove the 32 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



41. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH


    A160736E02
  1. Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.



    A160737E02
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.



42. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH


    A160738E01
  1. Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.



    A160739E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.

    HINT:
    Be sure to arrange the removed parts for each installation position separately.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head.
    2. Head warpage or cracking could result from removing bolts in an incorrect order.



43. REMOVE CYLINDER HEAD GASKET LH


44. REMOVE CYLINDER HEAD GASKET RH


45. REMOVE CYLINDER BLOCK WATER JACKET SPACER


A161997
  1. Remove the 2 water jacket spacers from the cylinder head.

    NOTICE:
    Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



46. REMOVE OIL RETURN PIPE GASKET


    A161914
  1. Using a screwdriver, pry out the oil return pipe gasket.

    HINT:
    Tape the screwdriver tip before use.



47. REMOVE VENTILATION PIPE GASKET


    A161915
  1. Using a screwdriver, pry out the ventilation pipe gasket.

    HINT:
    Tape the screwdriver tip before use.



48. REMOVE NO. 1 HEAT EXCHANGER COVER


    A161916E01
  1. Remove the 12 bolts and 2 nuts.



    A164347
  1. Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.

    HINT:
    Tape the screwdriver tip before use.



49. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A160720E01
  1. Remove the 14 bolts and 2 nuts.



    A120816
  1. Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.



50. REMOVE NO. 1 OIL PAN SUB-ASSEMBLY


    A160721E02
  1. Remove the 14 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.



    A160722E01
  1. Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.



51. REMOVE NO. 1 OIL PAN BAFFLE PLATE


    A160723
  1. Remove the 7 bolts and baffle plate.



52. REMOVE OIL STRAINER SUB-ASSEMBLY


    A160724
  1. Remove the 2 bolts, oil strainer and O-ring.



53. REMOVE ENGINE REAR OIL SEAL RETAINER


    A145612
  1. Remove the 6 bolts and oil seal retainer.



    A145613
  1. Using a screwdriver, pry out the oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.



54. REMOVE OIL DRAIN PIPE SUB-ASSEMBLY


    A160728
  1. Remove the bolt and oil drain pipe.

  1. Remove the O-ring.



55. REMOVE REAR CRANKSHAFT OIL SEAL


    A145614E01
  1. Place the oil seal retainer on wooden blocks.

  1. Using a screwdriver and hammer, tap out the oil seal.



56. REMOVE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.



57. REMOVE STUD BOLT

NOTICE:
If the stud bolt is deformed or its threads are damaged, replace it.