Home › ENGINE ยท 3UR-FE › INTAKE › INTAKE MANIFOLD

INTAKE MANIFOLD > REMOVAL

for Preparation Click here



1. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


2. REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Disconnect the washer hose and detach the 2 wire harness clamps.



  1. Remove the 7 bolts and cowl top outer panel sub-assembly.


    A215877



3. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap. Then drain the coolant from the radiator.

  1. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.



  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A151835E01

  1. Tighten the radiator drain cock plug by hand.



5. REMOVE V-BANK COVER SUB-ASSEMBLY


    A165576E04
  1. Raise the front of the V-bank cover sub-assembly to detach the 2 pins. Then remove the 2 V-bank cover hooks from the No. 1 V-bank cover bracket, and remove the V-bank cover sub-assembly.
    Text in Illustration 
    *1
    V-bank Cover Grommet
    *2
    Pin
    *3
    No. 1 V-bank Cover Bracket
    *4
    V-bank Cover Hook



6. REMOVE AIR CLEANER HOSE ASSEMBLY


    A187008
  1. Disconnect the vacuum hose from the air cleaner hose assembly.

  1. Slide the clamp and disconnect the ventilation hose from the air cleaner hose assembly.

  1. Loosen the 2 hose clamps.

  1. Remove the air cleaner hose assembly.



7. DISCONNECT VENTILATION HOSE ASSEMBLY


    A162091E01
  1. Slide the 2 clamps and disconnect the ventilation hose assembly from the ventilation pipe of the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.



8. REMOVE INTAKE MANIFOLD


    A162089
  1. Remove the No. 1 engine cover sub-assembly.



    A162090
  1. Remove the No. 3 engine cover.

  1. Disconnect the throttle body connector from the throttle body assembly.



    A307759
  1. Slide the 2 clamps and disconnect the 2 water by-pass hoses from the inlet water housing and front water by-pass joint.



    A162103
  1. Slide the clamp and disconnect the ventilation hose from the intake manifold.



    A162082
  1. Disconnect the 2 vacuum switching valve connectors.

  1. Slide the clamp and disconnect the purge line hose from the purge VSV.



    A165518
  1. Remove the 2 bolts to disconnect the No. 1 tube.

  1. Slide the clamp and disconnect the union to connector tube hose from the No. 1 tube.



    A165471
  1. Detach the 3 wire harness clamps from the 3 wire harness clamp brackets.



    A165472
  1. Remove the bolt and wire harness clamp bracket from the intake manifold.



    A165478
  1. Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.



9. REMOVE VENTILATION HOSE ASSEMBLY


    A163820E02
  1. Remove the 2 bolts and ventilation hose assembly from the intake manifold.



10. REMOVE NO. 1 V-BANK COVER BRACKET


    A162104
  1. Remove the 2 bolts and No. 1 V-bank cover bracket.



11. REMOVE V-BANK COVER BOLT


    A162100E01
  1. Remove the 2 V-bank cover bolts from the intake manifold.



12. REMOVE THROTTLE BODY ASSEMBLY


    A198574
  1. Remove the 4 bolts, throttle body assembly and gasket.



13. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    A164145
  1. Disconnect the 2 vacuum hoses from the vacuum switching valve assembly.

  1. Remove the bolt and vacuum switching valve assembly.



14. REMOVE PURGE VSV


    A168583
  1. Slide the clamp and disconnect the purge line hose from the intake manifold.

  1. Remove the bolt and purge VSV.



15. REMOVE UNION TO CONNECTOR TUBE HOSE


    A162101
  1. Slide the clamp and remove the union to connector tube hose from the intake manifold.

  1. Remove the 2 bolts and 2 wire harness clamp brackets.