EXHAUST MANIFOLD > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 3 screws and 5 bolts.
Unhook the engine under cover from the vehicle body as shown in the illustration.
| 4. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap. Then drain the coolant from the radiator.
Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.
Tighten the 2 cylinder block drain cock plugs.

Tighten the radiator drain cock plug by hand.
| 5. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Raise the front of the V-bank cover sub-assembly to detach the 2 pins. Then remove the 2 V-bank cover hooks from the No. 1 V-bank cover bracket, and remove the V-bank cover sub-assembly.
| *1 | V-bank Cover Grommet |
| *2 | Pin |
| *3 | No. 1 V-bank Cover Bracket |
| *4 | V-bank Cover Hook |
| 6. REMOVE AIR CLEANER HOSE ASSEMBLY |
![]() |
Disconnect the vacuum hose from the air cleaner hose assembly.
Slide the clamp and disconnect the ventilation hose from the air cleaner hose assembly.
Loosen the 2 hose clamps.
Remove the air cleaner hose assembly.
| 7. REMOVE AIR CLEANER ASSEMBLY |
![]() |
Remove the air cleaner cap.
Disconnect the MAF meter connector.
Using a clip remover, detach the wire harness clamp.
for Type A:
Unfasten the 4 hook clamps and then remove the air cleaner cap.
for Type B:
Unfasten the 2 hook clamps and then remove the air cleaner cap.
Remove the air cleaner element.
![]() |
Remove the 2 bolts and air cleaner case.
| 8. DISCONNECT INLET RADIATOR HOSE |
| 9. DISCONNECT OUTLET RADIATOR HOSE |
| 10. REMOVE FAN AND GENERATOR V-BELT |
![]() |
While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of φ 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
Remove the V belt.
| 11. REMOVE FAN SHROUD |
![]() |
Loosen the 4 nuts holding the fan with fluid coupling.
Remove the fan and generator V-belt.
Disconnect the reservoir hose from the upper radiator tank.
![]() |
for Condenser with Integrated Oil Cooler:
Detach the claw and open the No. 1 flexible hose clamp.
![]() |
Remove the 2 bolts holding the fan shroud.
Remove the 4 nuts of the fan with fluid coupling, and then remove the fan shroud together with the fan with fluid coupling.
Remove the fan pulley from the fan bracket.
| 12. REMOVE FRONT FENDER APRON SEAL RH |
Remove the 6 clips and fender apron seal.
| 13. REMOVE FRONT FENDER APRON SEAL REAR RH |
Remove the 5 clips and fender apron seal.
| 14. REMOVE FRONT FENDER APRON SEAL LH |
Remove the 6 clips and fender apron seal.
| 15. REMOVE FRONT FENDER APRON SEAL REAR LH |
Remove the 5 clips and fender apron seal.
| 16. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the dipstick.
![]() |
Remove the bolt and dipstick guide.
Remove the O-ring from the dipstick guide.
| 17. DISCONNECT VANE PUMP ASSEMBLY |
![]() |
Detach the 2 clamps and disconnect the power steering oil pressure switch connector.
![]() |
Remove the 2 bolts and disconnect the vane pump.
| 18. REMOVE GENERATOR ASSEMBLY |
![]() |
Disconnect the generator connector.
Remove the terminal cap and nut, and disconnect the generator wire.
![]() |
Remove the bolt and disconnect the wire harness bracket from the generator.
![]() |
Remove the 3 bolts, nut and generator.
| 19. DISCONNECT COOLER COMPRESSOR ASSEMBLY |
![]() |
Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.
| 20. REMOVE FRONT PROPELLER SHAFT ASSEMBLY |
| 21. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
| 22. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Put matchmarks on the No. 2 steering intermediate shaft and steering intermediate shaft.
Remove the bolt and disconnect the No. 2 steering intermediate shaft from the steering intermediate shaft.
![]() |
Put matchmarks on the No. 2 steering intermediate shaft and the power steering gear.
Remove the bolt and disconnect the No. 2 steering intermediate shaft from the power steering gear.
| 23. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and heat insulator.
| 24. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Remove the 10 nuts, exhaust manifold and 2 gaskets.
| 25. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Remove the 3 bolts and heat insulator.
| 26. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Remove the 10 nuts, exhaust manifold and 2 gaskets.