Home › ENGINE ยท 3UR-FBE › ENGINE CONTROL SYSTEM › AIR FUEL RATIO SENSOR

AIR FUEL RATIO SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)


    A194685
  1. Install the air fuel ratio sensor to the front exhaust pipe assembly by hand.



    A194686E04
  1. Using SST, tighten the air fuel ratio sensor.

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *a
    Fulcrum length

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.



2. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    A194685
  1. Install the air fuel ratio sensor to the front No. 2 exhaust pipe assembly by hand.



    A194686E05
  1. Using SST, tighten the air fuel ratio sensor.

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *a
    Fulcrum length

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.



3. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket and the front exhaust pipe assembly to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front exhaust pipe assembly to the center exhaust pipe with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Attach the 2 clamps and connect the heated oxygen sensor connector.



4. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Connect the front No. 2 exhaust pipe assembly to the exhaust pipe support.

  1. Install a new gasket and the front No. 2 exhaust pipe assembly to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 554 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front No. 2 exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.



5. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
  1. Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange, differential flange and transfer flange.



  1. for Front Differential Side:



      C158457E02
    1. Align the matchmarks on the differential and propeller shaft flange.
      Text in Illustration 
      *a
      for Front Differential Side
      *b
      Matchmark

    2. Install the propeller shaft with the 4 washers and 4 nuts.

      Torque:
      80 N*m{ 819 kgf*cm , 59 ft.*lbf }



    C158456E03
  1. for Transfer Side:

    1. Align the matchmarks on the transfer and propeller shaft flange.
      Text in Illustration 
      *a
      for Transfer Side
      *b
      Matchmark

    2. Connect the propeller shaft with the 4 washers and 4 nuts.

      Torque:
      80 N*m{ 819 kgf*cm , 59 ft.*lbf }



6. INSTALL PROPELLER SHAFT HEAT INSULATOR


C158452
  1. Install the heat insulator to the heat insulator bracket with the 2 bolts.

    Torque:
    16 N*m{ 160 kgf*cm , 12 ft.*lbf }



7. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.