Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM


A164725E02


INSPECTION PROCEDURE

1.CHECK INJECTOR ASSEMBLY (POWER SOURCE)
A245668E01
  1. Disconnect the injector connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    H1-2 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    F1-2 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    H2-2 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    F2-2 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    H3-2 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    F3-2 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 7
    H4-2 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 8
    F4-2 - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 4
OK


2.INSPECT INJECTOR ASSEMBLY
  1. Inspect the injector .

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
  1. Disconnect the injector connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    H1-1 - Body ground
    Always
    10 kΩ or higher
    H1-1 - D74-86 (#10)
    Always
    Below 1 Ω
    No. 2
    F1-1 - Body ground
    Always
    10 kΩ or higher
    F1-1 - D74-109 (#20)
    Always
    Below 1 Ω
    No. 3
    H2-1 - Body ground
    Always
    10 kΩ or higher
    H2-1 - D74-85 (#30)
    Always
    Below 1 Ω
    No. 4
    F2-1 - Body ground
    Always
    10 kΩ or higher
    F2-1 - D74-108 (#40)
    Always
    Below 1 Ω
    No. 5
    H3-1 - Body ground
    Always
    10 kΩ or higher
    H3-1 - D74-84 (#50)
    Always
    Below 1 Ω
    No. 6
    F3-1 - Body ground
    Always
    10 kΩ or higher
    F3-1 - D74-107 (#60)
    Always
    Below 1 Ω
    No. 7
    H4-1 - Body ground
    Always
    10 kΩ or higher
    H4-1 - D74-83 (#70)
    Always
    Below 1 Ω
    No. 8
    F4-1 - Body ground
    Always
    10 kΩ or higher
    F4-1 - D74-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.INSPECT FUSE (INJ, IG2 MAIN)
A166990E01
  1. Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ fuse
    Always
    Below 1 Ω
    IG2 MAIN fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


5.INSPECT INTEGRATION RELAY (IG2)
  1. Inspect the integration relay (Click here).



NG
REPLACE INTEGRATION RELAY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - INJECTOR ASSEMBLY)