Home › RESTRAINTS › SEAT BELT › REAR CENTER SEAT OUTER BELT ASSEMBLY (for CrewMax)

REAR CENTER SEAT OUTER BELT ASSEMBLY (for CrewMax) > INSTALLATION

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY
  1. Attach the guide to install the rear center seat outer belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B353874
  1. Attach the 3 guides to install the rear center seat outer belt assembly to the rear seat shoulder belt hole cover.



2. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    B353871
  1. Pass the floor anchor of the rear center seat outer belt assembly through the hole of the separate type rear seatback cover with pad in the direction indicated by the arrow shown in the illustration.

  1. Attach the 8 hooks to install the separate type rear seatback cover with pad.

  1. Attach the 2 guides to install the upper rear seatback lock bezel of the rear center seat outer belt assembly with the screw.



    B353866E01
  1. Pass the rear center seat outer belt assembly through the rubber band of the separate type rear seatback cover.
    Text in Illustration 
    *1
    Rubber Band
    *2
    Protruding Part

  1. Connect the floor anchor of the rear center seat outer belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    The anchor part of the rear center seat outer belt assembly must not overlap the protruding part.



3. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
  1. Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.



4. INSTALL REAR SEAT HEADREST SUPPORT
  1. Attach the 4 claws to install the 2 rear seat headrest supports.



5. INSTALL TETHER ANCHOR BRACKET SUB-ASSEMBLY


    B353862
  1. Install the 2 tether anchor bracket sub-assemblies with the 2 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the 2 hooks of the separate type rear seatback cover.



6. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY
  1. Install the rear seat armrest bracket and 2 bushes to the rear seat center armrest assembly.

  1. Using a T25 "TORX" socket wrench, install the 2 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }

  1. Install the rear seat center armrest assembly with the 3 nuts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



7. INSTALL REAR SEAT INNER RECLINING COVER LH


    B353852
  1. Attach the 2 guides in the direction indicated by the arrow shown in the illustration.

  1. Attach the clip.

  1. Using a T25 "TORX" socket wrench, install the rear seat inner reclining cover LH with the screw.



8. INSTALL REAR SEAT RECLINING COVER LH
  1. Attach the guide and claw.

  1. Using a T25 "TORX" socket wrench, install the rear seat reclining cover LH with the 2 screws.



9. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD


  1. Attach the 6 hooks to install the separate type rear seat cushion cover with pad.


    B353844



10. INSTALL REAR SEATBACK LOCK CONTROL BEZEL
  1. Attach the 4 claws to install the rear seatback lock control bezel.



    B353842
  1. Close the 2 fasteners and attach the 2 hooks to close the separate type rear seat cushion cover.



  1. Fold in the 2 fasteners.


    B353840



11. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
  1. Push the lock release button to release the lock, and then install the rear center seat headrest assembly.



12. INSTALL REAR SEAT HEADREST ASSEMBLY
  1. Push the 2 lock release buttons to release the lock, and then the rear seat headrest assembly.



13. INSTALL REAR SEAT ASSEMBLY LH
  1. Install the rear seat assembly LH with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Be careful not to damage the vehicle body.



    B355145
  1. Pull the No. 1 reclining adjuster release handle LH and fold down the seat cushion.



14. INSTALL REAR SEAT INNER BELT ASSEMBLY


    B355201E01
  1. Pass the rear seat inner belt assembly through the rubber band of the separate type rear seatback cover in the direction indicated by the arrow shown in the illustration.
    Text in Illustration 
    *1
    Rubber Band
    *2
    Protruding Part

  1. Install the rear seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor of the rear seat inner belt assembly to overlap the protruding part.



15. INSTALL REAR SEAT ASSEMBLY RH
  1. Install the rear seat assembly RH with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Be careful not to damage the vehicle body.



    B355146
  1. Pull the No. 1 reclining adjuster release handle RH and fold down the seat cushion.