Home › BODY ELECTRICAL › DOOR LOCK › REAR DOOR LOCK (for CrewMax)

REAR DOOR LOCK (for CrewMax) > INSTALLATION

for Preparation Click here



1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    B167682E01
  1. Install the rear door inside locking cable.



    B266908
  1. Attach the 3 claws.



2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    B169264E01
  1. Install the rear door lock remote control cable.



    B266912
  1. Attach the claw.



3. INSTALL REAR DOOR LOCK ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating parts of the rear door lock.

  1. Install a new door lock wire harness packing to the door lock.

    NOTICE:
    1. When reusing a door lock that has been removed, replace the packing in the connecting part with new packing.
    2. Be careful that no grease or dirt sticks to the packing surface in the connecting part.
    3. Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.



    B169263
  1. Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    B171301
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Be careful not to damage the glass.

  1. Install the door glass to the window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



5. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    B169259
  1. Install the rear door rear lower window frame to the door panel with the 2 bolts.



6. INSTALL REAR DOOR GLASS RUN LH


    B169257
  1. Install the rear door glass run.



7. INSTALL REAR DOOR SERVICE HOLE COVER LH


    B169256
  1. Attach the 5 clamps to install the rear door service hole cover.

    NOTICE:
    1. When installing the service hole cover, pull out the links through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.



8. INSTALL REAR NO. 2 DOOR TRIM BRACKET


    B266909
  1. Install the bracket with the 2 screws.



9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    B165684E03
  1. Connect the 2 cables to the inside handle.



    B169254E01
  1. Attach the inside handle's knob to the door trim board.

  1. for 12 Speakers:

    1. Connect the connector.

  1. Attach the 10 clips to install the door trim board.

  1. Install the inside handle and door trim board to the door trim panel with the screw.

  1. Install the door trim board to the door panel with the screw.

  1. Install the clip.



10. INSTALL REAR DOOR ARMREST COVER LH


11. INSTALL REAR DOOR FRAME GARNISH LH


    B169253
  1. Attach the 5 clips to install the rear door frame garnish.



12. INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH


    E278383
  1. Connect the connector.



    E278385
  1. Attach the 2 clips and 5 claws to install the rear upper door armrest base panel LH.



13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    B168093
  1. Attach the 4 claws to install the bezel plug.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL