Home › BODY › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Driver Seat / Data List.

  5. Read the Data List according to the display on the Techstream.

    Driver Seat 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Reclining Rear
    Reclining switch signal (Rearward) / ON or OFF
    ON: Reclining switch (Rearward) on
    OFF: Reclining switch (Rearward) off
    -
    Reclining Front
    Reclining switch signal (Forward) / ON or OFF
    ON: Reclining switch (Forward) on
    OFF: Reclining switch (Forward) off
    -
    Front Vertical Down
    Front vertical switch signal (Downward) / ON or OFF
    ON: Front vertical switch (Downward) on
    OFF: Front vertical switch (Downward) off
    -
    Front Vertical Up
    Front vertical switch signal (Upward) / ON or OFF
    ON: Front vertical switch (Upward) on
    OFF: Front vertical switch (Upward) off
    -
    Lifter Switch Down
    Lifter switch signal (Downward) / ON or OFF
    ON: Lifter switch (Downward) on
    OFF: Lifter switch (Downward) off
    -
    Lifter Switch Up
    Lifter switch signal (Upward) / ON or OFF
    ON: Lifter switch (Upward) on
    OFF: Lifter switch (Upward) off
    -
    Slide Rear
    Sliding switch signal (Rearward) / ON or OFF
    ON: Sliding switch (Rearward) on
    OFF: Sliding switch (Rearward) off
    -
    Slide Front
    Sliding switch signal (Forward) / ON or OFF
    ON: Sliding switch (Forward) on
    OFF: Sliding switch (Forward) off
    -
    SET Switch
    Seat memory switch SET signal / ON or OFF
    ON: Seat memory switch SET on
    OFF: Seat memory switch SET off
    -
    M1 Switch
    Seat memory switch M1 signal / ON or OFF
    ON: Seat memory switch M1 on
    OFF: Seat memory switch M1 off
    -
    M2 Switch
    Seat memory switch M2 signal / ON or OFF
    ON: Seat memory switch M2 on
    OFF: Seat memory switch M2 off
    -
    Seat Memory No1
    Seat position memorized with M1 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Seat Memory No2
    Seat position memorized with M2 switch / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Ignition Switch
    Communication state of ignition switch signal / ON or OFF
    ON: Ignition switch ON signal received
    OFF: Ignition switch off signal not received
    -
    Key Switch
    Ignition switch status / ON or OFF
    ON: Ignition switch ON
    OFF: Ignition switch off
    "OFF" is also displayed for this item when the ignition switch is ACC
    Key Code Confirm
    Recognition code is registered / ON or OFF
    ON: One more recognition codes registered
    OFF: No recognition code registered
    -
    D-Door Courtesy
    Front door courtesy light switch assembly signal / ON or OFF
    ON: Driver door open
    OFF: Driver door closed
    -
    P Switch
    Park state signal / ON or OFF
    ON: Shift lever in P
    OFF: Shift lever in a position other than P
    -
    Parking Brake SW
    Parking brake switch status / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Vehicle Speed
    Vehicle speed data / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    Power Voltage
    Power supply for position control ECU and switch assembly / Min: 0 V, Max: 19.89 V
    Within range from 11 to 14 V
    -
    Slide Position
    Seat sliding position / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Reclining Position
    Seat reclining position / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Front Vertical Position
    Seat front vertical position / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Lifter Position
    Seat lifter position / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Slide Pos Mem No1
    Seat sliding position memorized with M1 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Reclining Pos Mem No1
    Seat reclining position memorized with M1 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Frnt Vrtcl Pos Mem No1
    Front vertical position memorized with M1 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Lifter Pos Mem No1
    Lifter position memorized with M1 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Slide Pos Mem No2
    Seat sliding position memorized with M2 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Reclining Pos Mem No2
    Seat reclining position memorized with M2 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Frnt Vrtcl Pos Mem No2
    Front vertical position memorized with M2 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Lifter Pos Mem No2
    Lifter position memorized with M2 switch / Min: 0000, Max: 65535
    Within range of 0 to 65535
    (Seat position displayed)
    -
    Memory No1
    Seat memory switch M1 signal / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Memory No2
    Seat memory switch M2 signal / Mem or Not Mem
    Mem: Memorized
    Not Mem: Not memorized
    -
    Motor Status
    State of slide motor control / STANDBY, MOVING, LOCK
    STANDBY: Slide motor idle
    MOVING: Slide motor moving
    LOCK: Slide motor locked
    -
    Slide Position Rear Limit
    Seat sliding position / Min: 0000, Max: 65535
    Within range of 0 to 65535
    -
    Return Move
    Return destination / AVAIL or NOT AVL
    AVAIL: Return destination set
    NOT AVL: Return destination not set
    -
    Return & Away Function
    Power easy access system status / AVAIL or NOT AVL
    AVAIL: Power easy access system functioning
    NOT AVL: Power easy access system not functioning
    -
    Driver Seat Buckle SW
    Status of the driver seat belt / ON or OFF
    ON: Tongue plate is engaged
    OFF: Tongue plate is not engaged
    -
    Return Position
    Return position / Min: 0000, Max: 65535
    Within range of 0 to 65535
    -
    Seat Travel Distance
    Setting of the customized item "Seat Travel Distance" / OFF, Short, Normal
    Customized value displayed
    -
    Number of Trouble Codes
    Number of trouble codes / Min.: 0 ,or Max.: 255
    Number of DTCs will be displayed
    -

  6. Enter the following menus: Body Electrical / Main Body / Data List.

  7. Read the Data List according to the display on the Techstream.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy
    Front door courtesy light switch assembly signal / ON or OFF
    ON: Driver door open
    OFF: Driver door closed
    -


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Driver Seat / Active Test.

  5. Perform the Active Test according to the display on the Techstream.

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    Front / OFF / Rear
    -
    Front Vertical Operation
    Seat front vertical operation
    Up / OFF / Down
    -
    Lifter Operation
    Seat lifter operation
    Up / OFF / Down
    -
    Seat Slide Operation
    Seat sliding operation
    Front / OFF / Rear
    -
    Buzzer
    Buzzer operation
    ON / OFF
    -