Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P144C    Open in Secondary Air Injection System Heater Control Circuit

DTC    P144D    Short in Secondary Air Injection System Heater Control Circuit

for Preparation Click here


DESCRIPTION

The ECM operates the air pump heater relay which causes the air pump heater to operate.

DTC No.
DTC Detection Condition
Trouble Area
P144C
Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay circuit
  2. Air pump heater relay
  3. ECM
P144D
Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic).
  1. Open or short in air pump heater relay circuit
  2. Air pump heater relay
  3. ECM

MONITOR DESCRIPTION

These DTCs are designed to detect a malfunction in the air pump heater relay circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the air pump heater relay is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the air pump heater relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.
  1. The battery voltage is not applied to terminal HAI1 while the air pump heater relay is off.
  2. The battery voltage is applied to terminal HAI1 while the air pump heater relay is on.

MONITOR STRATEGY


Related DTCs
P144C: Air pump heater relay circuit range check (Low voltage)
P144D: Air pump heater relay circuit range check (High voltage)
Required Sensors/Components (Main)
Air pump heater relay
Required Sensors/Components (Related)
-
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


Case 1 
Monitor runs whenever following DTCs not stored
None
Current air pump heater relay (AIR PMP HTR)
ON
Last air pump heater relay (AIR PMP HTR)
ON
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

Case 2 
Monitor runs whenever following DTCs not stored
None
Current air pump heater relay (AIR PMP HTR)
OFF
Last air pump heater relay (AIR PMP HTR)
OFF
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


P144C 
Air pump heater relay output terminal voltage
Low

P144D 
Air pump heater relay output terminal voltage
High

CONFIRMATION DRIVING PATTERN


A231721E10

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and wait 10 seconds or more [B].
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  8. Read the pending DTC.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P144C or P144D.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0412 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AIR PUMP HEATER RELAY
  1. Inspect the air pump heater relay (Click here).



NG
REPLACE AIR PUMP HEATER RELAY
OK


2.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
  1. Remove the air pump heater relay (AI-HTR).



    A258729E09
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    AI-HTR relay terminal 1 - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reinstall the air pump heater relay (AI-HTR).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER RELAY)
  1. Remove the air pump heater relay (AI-HTR).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    AI-HTR relay terminal 2 - D74-61 (HAI1)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    AI-HTR relay terminal 2 or D74-61 (HAI1) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the air pump heater relay (AI-HTR).

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)