Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

BLIND SPOT MONITOR SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.

  5. Read the Data List according to the display on the Techstream.

    Blind Spot Monitor Master 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main Switch
    Blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON
    ON: Blind spot monitor main switch assembly (warning canceling switch assembly) on
    OFF: Blind spot monitor main switch assembly (warning canceling switch assembly) off
    -
    Warning Indicator Turning on (Master)
    State of the outer rear view mirror indicator RH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in warning area
      3. Vehicle speed 16 km/h (10 mph) or more
      4. Shift lever in any position except R
      5. No DTC output
    -
    Warning Indicator Flashing (Master)
    State of the outer rear view mirror indicator RH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in warning area
      3. Vehicle speed 16 km/h (10 mph) or more
      4. Shift lever in any position except R
      5. No DTC output
    -
    Main Switch Indicator Status
    State of the blind spot monitor indicator on the blind spot monitor main switch assembly (warning canceling switch assembly) / OFF or ON
    OFF: Indicator not illuminated
    ON: Indicator illuminated
    -
    Warning Indicator Input Circuit Voltage
    Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
    Not illuminated: 0 V
    Illuminated: 2.5 to 7.5 V
    -
    Warning Indicator Input Circuit Current
    Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
    Not illuminated: 0 mA
    Illuminated: 5 to 100 mA
    -
    Right Turn SW State (CAN)
    State of the headlight dimmer switch assembly (right turn signal light switch) / ON or OFF
    ON: Right side of turn signal light switch on
    OFF: Right side of turn signal light switch off
    -
    Left Turn SW State (CAN)
    State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF
    ON: Left side of turn signal light switch on
    OFF: Left side of turn signal light switch off
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -
    Indicator Light Control State
    Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
    Dim OFF: Indicator not dimmed
    Dim ON: Indicator dimmed
    -
    HV Flag
    Hybrid vehicle / OFF or ON
    OFF: Non-hybrid vehicle
    ON: Hybrid vehicle
    -
    VGRS Flag
    VGRS installed / OFF or ON
    OFF: VGRS not installed
    ON: VGRS installed
    -
    Main SW Inspection Completeness Flag
    Completion of inspection for blind spot monitor main switch assembly (warning canceling switch assembly) / Incompl or Compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when the blind spot monitor main switch assembly (warning canceling switch assembly) is changed from off to on during Test Mode.
    Beam Axis Inspection Completeness Flag
    Completion of beam axis inspection / Incompl or Compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when Test Mode has been entered.
    Destination Undefined Flag
    Destination determination / Unfixed or Fixed
    Unfixed: Sensor destination information not determined
    Fixed: Sensor destination information determined according to CAN destination information
    -
    Angle Adjustment by Auto Alignment
    Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
    Angle adjusted using auto alignment is displayed
    When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
    Setting of Warning Indicator Current (Dim OFF)
    Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA
    Always: 0 to 100 mA
    -
    Setting of Warning Indicator Current (Dim ON)
    Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA
    Always: 0 to 100 mA
    -
    Mirror LED Duty Ratio (Blinking)
    Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100%
    Always: 50%
    -
    Number of DTC
    Number of DTC / Min.: 0, Max.: 255
    When system is normal: 0
    When a malfunction is detected: More than 0
    -

    Blind Spot Monitor Slave 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Warning Indicator Turning on (Slave)
    State of the outer rear view mirror indicator LH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in warning area
      3. Vehicle speed 16 km/h (10 mph) or more
      4. Shift lever in any position except R
      5. No DTC output
    -
    Warning Indicator Flashing (Slave)
    State of the outer rear view mirror indicator LH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in warning area
      3. Vehicle speed 16 km/h (10 mph) or more
      4. Shift lever in any position except R
      5. No DTC output
    -
    Buzzer Sound Status
    State of the rear cross traffic alert buzzer (blind spot monitor buzzer) / OFF or ON
    OFF: Buzzer not sounding
    1. ON: All of the following conditions are met:
      1. Not during initial check
      2. Vehicle detected in warning area of rear cross traffic alert
      3. Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more
      4. Shift lever in R
      5. No DTC output
    -
    Warning Indicator Input Circuit Voltage
    Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
    Not illuminated: 0 V
    Illuminated: 2.5 to 7.5 V
    -
    Warning Indicator Input Circuit Current
    Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
    Not illuminated: 0 mA
    Illuminated: 5 to 100 mA
    -
    Buzzer Input Circuit Voltage
    Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V
    Not sounding buzzer: 11 to 14 V
    Sounding buzzer: Alternating between 0 to 14 V
    -
    Right Turn SW State (CAN)
    State of the headlight dimmer switch assembly (right turn signal light switch) / ON or OFF
    ON: Right side of turn signal light switch on
    OFF: Right side of urn signal light switch off
    -
    Left Turn SW State (CAN)
    State of the headlight dimmer switch assembly (left turn signal light switch) / ON or OFF
    ON: Left side of turn signal light switch on
    OFF: Left side of urn signal light switch off
    -
    Reverse
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -
    Indicator Light Control State
    Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
    Dim OFF: Indicator not dimmed
    Dim ON: Indicator dimmed
    -
    HV Flag
    Hybrid vehicle / OFF or ON
    OFF: Non-hybrid vehicle
    ON: Hybrid vehicle
    -
    VGRS Flag
    VGRS installed / OFF or ON
    OFF: VGRS not installed
    ON: VGRS installed
    -
    Beam Axis Inspection Completeness Flag
    Completion of beam axis inspection / Incompl or Compl
    Incompl: Inspection not completed
    Compl: Inspection completed
    Changes to Compl when Test Mode has been entered.
    Destination Undefined Flag
    Destination determination / Unfixed or Fixed
    Unfixed: Sensor destination information not determined
    Fixed: Sensor destination information determined according to CAN destination information
    -
    Angle Adjustment by Auto Alignment
    Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
    Angle adjusted using auto alignment is displayed
    When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
    Setting of Warning Indicator Current (Dim OFF)
    Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA
    Always: 0 to 100 mA
    -
    Setting of Warning Indicator Current (Dim ON)
    Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA
    Always: 0 to 100 mA
    -
    Mirror LED Duty Ratio (Blinking)
    Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100%
    Always: 50%
    -
    Buzzer Control Frequency
    Frequency of the rear cross traffic alert buzzer (blind spot monitor buzzer) when sounding / Min.: 1000 Hz, Max.: 2400 Hz
    Always: 2400 Hz
    -
    Number of DTC
    Number of DTC / Min.: 0, Max.: 255
    When system is normal: 0
    When a malfunction is detected: More than 0
    -