Home › ENGINE ยท 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > INITIALIZATION

for Preparation Click here



Fuel Density Learning Value Reset

NOTICE:
Performing "Fuel Density Learning Value Reset" initializes the alcohol concentration learned value. If learning of the alcohol concentration is not performed after performing initialization, DTCs may be stored. Do not perform initialization unless specified in the repair manual.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel Density Learning Value Reset.

  5. After the completion of learned value initialization, confirm the air fuel ratio learned values (A/F Learn Value Idle #1, A/F Learn Value Low #1, A/F Learn Value Mid1 #1, A/F Learn Value Mid2 #1, A/F Learn Value High #1, A/F Learn Value Idle #2, A/F Learn Value Low #2, A/F Learn Value Mid1 #2, A/F Learn Value Mid2 #2 or A/F Learn Value High #2) in the Data List.

  6. Confirm the following conditions as instructed on the screen.

    1. Ignition switch: ON

    2. Engine: stopped

    3. Battery voltage: 9 V or higher

  7. After confirming, select "Next" and initialize the learned value.

    HINT:
    If a message indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform learned value initialization again.

    Result:
    If 0 is displayed for all the air fuel ratio learned values, initialization has completed correctly. If a value other than 0 is displayed for one of the air fuel ratio learned values, perform initialization again.

  8. Turn the ignition switch off and wait for at least 30 seconds.

  9. Turn the ignition switch to ON.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel Density Learning Value Reset.

    HINT:
    1. After clearing the learned value, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.
    2. If "Fuel Density Learning Value Reset" is performed after warming the engine coolant up to approximately 50°C (122°F), the engine becomes easier to start afterward.

  11. Confirm the following conditions as instructed on the screen.

    1. Ignition switch: ON

    2. Engine: stopped

    3. Battery voltage: 9 V or higher

  12. Press "Next".

    HINT:
    When "Next" is pressed, initialization is performed automatically.

  13. Turn the ignition switch off.

  14. Add at least 8 liters (2 gallons) of fuel.

    NOTICE:
    Add fuel immediately after resetting. (Do not start the engine before adding fuel.)

    HINT:
    1. Learning of the alcohol concentration will not be started until the ECM judges that the fuel gauge has moved after resetting. Add at least 8 liters (2 gallons) of fuel.
    2. Check "Fuel Remaining Volume" in the Data List and if it has a value of 85% or more, remove enough fuel so that the value decreases to less than 85% before adding fuel.



  15. Turn the ignition switch to ON and turn the Techstream on [A].


    A263137E29

  16. Enter the following menus: Powertrain / Engine and ECT / Data List / Flexible Fuel Vehicle / Alcohol Density Learning.

  17. Make sure that the Data List item "Alcohol Density Learning" is "Incmpl".

  18. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

  19. With the engine warmed up, idle the engine for 2 minutes or more [C].

  20. Drive the vehicle at a speed between 60 and 120 km/h (37 and 75 mph) and at an engine speed of between 1400 and 3200 rpm for 5 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  21. Stop the vehicle [E].

  22. Enter the following menus: Powertrain / Engine and ECT / Data List / Flexible Fuel Vehicle / Alcohol Density Learning.

  23. Make sure that the Data List item "Alcohol Density Learning" is "Compl".

    HINT:
    If "Incmpl" is displayed, perform the confirmation driving pattern again.

  24. Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density Estimate, Short FT #1, Short FT #2, Long FT #1 and Long FT #2.

  25. Check the data list values, and then write them down.

  26. Confirm the alcohol concentration in the fuel .

  27. Write down the alcohol concentration in the fuel.

  28. Use the following formula to calculate the difference between the current learned value and the actual alcohol concentration in the fuel.

    HINT:
    | (Alcohol Density Estimate / 2) - (Alcohol Concentration in Fuel / 2) | < 10%


    Standard:

    Result
    Specified Condition
    Difference between actual alcohol concentration and Alcohol Density Estimate
    Less than 10%
    Short FT #1, Short FT #2, Long FT #1 and Long FT #2
    Between -35% and 35%

    HINT:
    If the result is not as specified, replace the fuel with E0 gasoline (approximately 20 liters (5 gallons)) to increase the concentration of gasoline. Then perform "Fuel Density Learning Value Reset" again.

  29. Confirm that the idle speed is within the standard range.

    Standard:
    Engine Idle Speed
    650 to 750 rpm

    HINT:
    1. Be sure to perform this step with all accessories off.
    2. Make sure that the shift lever is in P or N.



  30. If the engine idle speed is not as specified, perform the following confirmation driving pattern.


    A250733E18


    1. Warm up the engine (engine coolant temperature is 80°C (176°F) or higher, air conditioning and all accessories are off) [A].

    2. Drive the vehicle at 10 km/h (6 mph) or more [B].

    3. Idle the engine for 20 seconds or more [C].

    4. Repeat procedure [B] and [C], and check that the idle speed is within the specified range [D].

      Standard:
      Engine Idle Speed
      650 to 750 rpm

      HINT:
      1. Be sure to perform this step with all accessories off.
      2. Make sure that the shift lever is in P or N.
      3. If the idle speed is still out of the specified range, repeat procedure [B] and [C] until the idle speed is within the specified range [E].