Point A, a on the vehicle are asymmetrical.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A, a | Back Door Hinge Installation Hole | φ15 (0.59) |
| B, b | Back Door Stay Installation Nut | M6 (0.24) |
| C, c | Roof Side Inner Reinforcement Corner | - |
| D, d | Roof Side Inner Reinforcement Corner | - |
| E, e | Quarter Panel Reinforcement Extension Corner | - |
| F, f | Quarter Panel Standard Hole | φ13 (0.51) |
| G, g | Back Door Opening Lower Reinforcement Corner | - |
| H, h | Back Door Lock Striker Installation Nut | M8 (0.31) |
| J, j | Rear Shock Absorber Installation Hole | φ24 (0.94) |
| K, k | Wheelhouse Inner Gusset Standard Hole | φ10 (0.39) |
| L, l | Center Body Pillar Assembly Mark | - |
|
Symmetric distance |
|
Asymmetric distance |
| *a | for 2WD | *b | for AWD |
| *c | mm
(in.) |
- | - |
| *W | Width distance | *L | Length distance |
| *X | Diagonal distance | - | - |
| *a | for 2WD | *b | for AWD |
| *c | mm
(in.) |
- | - |
| *W | Width distance | *L | Length distance |
| *X | Diagonal distance | - | - |
Gasoline Model
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A | Console Installation Nut | M6 (0.24) |
| B, b | Center Floor Crossmember No.1 Standard Hole | 16X13
(0.63X0.51) |
| C, c | Quarter Wheelhouse Inner Panel Standard Hole | φ10 (0.39) |
| D, d | Seat Belt Retractor Installation Nut | M6 (0.24) |
| E, e | Rear Shock Absorber Bracket Standard Hole | 13X10 (0.51X0.39) |
| F, f | Wheelhouse Inner Gusset Standard Hole | φ10 (0.39) |
| G, g | Roof Side Trim Installation Hole | φ8.5 (0.33) |
| H, h | Roof Side Trim Installation Hole | φ8.5 (0.33) |
| J, j | Deck Side Trim Installation Hole | φ8.5 (0.33) |
| K, k | Body Lower Back Panel Reinforce Standard Hole | φ10 (0.39) |
| L, l | Back Door Lock Striker Installation Nut | M8 (0.31) |
| M, m | Rear Combination Light Installation Hole | 9X9
(0.35X0.35) |
| N, n | Rear Combination Light Installation Hole | 9X9
(0.35X0.35) |
| O, o | Rear Bumper Installation Nut | M6 (0.24) |
| P, p | Rear Combination Light Installation Hole | 12X8
(0.47X0.31) |
| Q, q | Rear Bumper Retainer Installation Hole | 9X9
(0.35X0.35) |
| R, r | Crash Box Installation Nut | M8 (0.31) |
| *a | mm
(in.) |
- | - |
| *L | Length distance | - | - |
| *a | mm
(in.) |
- | - |
| *W | Width distance | *L | Length distance |
| *X | Diagonal distance | - | - |
HV Model
Point B, b on the vehicle are asymmetrical.
In cases in which only one dimension is given, left and right are symmetrical.
For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).
| Symbol | Name | Hole Diameter
mm (in.) |
|---|---|---|
| A | Console Installation Nut | M6 (0.24) |
| B | Center Floor Crossmember No.1 Standard Hole | 16X13
(0.63X0.51) |
| b | Center Floor Crossmember No.1 Standard Hole | φ13 (0.51) |
| C, c | Quarter Wheelhouse Inner Panel Standard Hole | φ10 (0.39) |
| D, d | Seat Belt Retractor Installation Nut | M6 (0.24) |
| E, e | Rear Shock Absorber Bracket Standard Hole | 13X10
(0.51X0.39) |
| F, f | Wheelhouse Inner Gusset Standard Hole | φ10 (0.39) |
| G, g | Roof Side Trim Installation Hole | φ8.5 (0.33) |
| H, h | Roof Side Trim Installation Hole | φ8.5 (0.33) |
| J, j | Deck Side Trim Installation Hole | φ8.5 (0.33) |
| K, k | Body Lower Back Panel Reinforce Standard Hole | φ10 (0.39) |
| L, l | Back Door Lock Striker Installation Nut | M8 (0.31) |
| M, m | Rear Combination Light Installation Hole | 9X9
(0.35X0.35) |
| N, n | Rear Combination Light Installation Hole | 9X9
(0.35X0.35) |
| O, o | Rear Bumper Installation Nut | M6 (0.24) |
| P, p | Rear Combination Light Installation Hole | 12X8
(0.47X0.31) |
| Q, q | Rear Bumper Retainer Installation Hole | 9X9
(0.35X0.35) |
| R, r | Crash Box Installation Nut | M8 (0.31) |
|
Symmetric distance |
|
Asymmetric distance |
| *a | for AWD | *b | for 2WD |
| *c | mm
(in.) |
- | - |
| *L | Length distance | *X | Diagonal distance |
| *a | mm
(in.) |
- | - |
| *W | Width distance | *L | Length distance |
| *X | Diagonal distance | - | - |