Home › Vehicle Exterior › BODY PANEL › REAR FLOOR PAN (for TMMF Made) › from 2021.07
BM3700E _01 Vehicle Exterior _094466 BODY PANEL _0485531 REAR FLOOR PAN(for TMMF Made) F

BODY PANEL  REAR FLOOR PAN(for TMMF Made)  ASSEMBLY REPLACEMENT  


K160060

With the body lower back panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.

a.

Remove the wheelhouse inner gusset front.

K159736C03
0.167,0.333 7,3.583 6.833,3.25 3.583,3.583 3.583,0.333 false 1.5,2.646 1.167,3.167 1.167,3.167 1.333,3.167 false 5.75,3.167 5.917,3.167 5.917,3.167 5.583,2.635 false 3.688,0.438 4,0.635 0.313,0.198 10 false *C 0.271,0.438 0.583,0.635 0.313,0.198 10 false *B 1.417,3.083 1.729,3.281 0.313,0.198 10 false *1 5.583,3.083 5.896,3.281 0.313,0.198 10 false *1 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for 2WD *B LH Side
*C RH Side - -
*1 WHEELHOUSE INNER GUSSET FRONT - -



b.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K162801C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for 2WD - -
K108837

Adhesive - -


K162802C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for 2WD - -


K162803C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for 2WD *B LH Side


K162804C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for 2WD *B RH Side



c.

Remove the center floor panel reinforcement sub-ssembly.

K162772C02
0.167,0.333 7,3.583 6.833,3.25 3.583,3.583 3.583,0.333 false 1.583,2.813 1.25,3.333 1.25,3.333 1.417,3.333 false 5.583,3.333 5.75,3.333 5.75,3.333 5.458,2.802 false 3.688,0.438 4,0.635 0.313,0.198 10 false *C 0.271,0.438 0.583,0.635 0.313,0.198 10 false *B 1.5,3.25 1.813,3.448 0.313,0.198 10 false *1 5.417,3.25 5.729,3.448 0.313,0.198 10 false *1 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for AWD *B LH Side
*C RH Side - -
*1 CENTER FLOOR PANEL REINFORCEMENT SUB-ASSEMBLY - -



d.

Roughly cut open the panel so that the adhesive can be reached. Cut through the adhesive with a cut chisel to remove the panel.

HINT:

In cases where the adhesive cannot be removed with a cut chisel, heat the adhesive with an industrial heater gun or gas burner taking care not to cause panel deformation by overheating.


K162809C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for AWD - -
K108837

Adhesive - -


K162810C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for AWD - -


K162811C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for AWD *B LH Side


K162812C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for AWD *B RH Side




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108830

Fillet Weld

a.

Before temporarily installing the new parts, weld the rear floor pan, spare wheel clamp bracket, rear floor side panel, actuator cover bracket no.3 and with the standard number of welding points.

K162805C01
0.667,0.25 6.5,6.583 5.833,6.333 0.667,3.5 6.5,3.5 false 3.167,0.844 2.917,0.5 2.917,0.5 2.75,0.5 false 4.385,3.167 4.219,3.167 4.219,3.167 3.583,1.917 false 1.833,6.25 2,6.25 2,6.25 2.667,5.583 false 2,6.25 2.677,5.083 false 3.75,6.417 3.583,6.417 3.583,6.417 3.083,5.604 false 3.583,6.417 3.094,4.906 false 3.583,6.417 3.938,4.667 false 3.583,6.417 4.01,5.302 false 3.583,6.417 4.25,5.698 false 4.25,4.917 4.667,4 4.667,4 4.833,4 false 1.813,2.5 1.979,2.5 1.979,2.5 2.313,2.75 false 4.833,2.75 5.167,2.5 5.167,2.5 5.333,2.5 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.771,0.354 1.083,0.552 0.313,0.198 10 false *B 0.771,3.604 1.083,3.802 0.313,0.198 10 false *C 2.583,0.417 2.896,0.615 0.313,0.198 10 false *1 4.438,3.083 4.75,3.281 0.313,0.198 10 false *2 1.604,6.167 1.917,6.365 0.313,0.198 10 false *5 3.833,6.333 4.146,6.531 0.313,0.198 10 false *5 4.917,3.917 5.229,4.115 0.313,0.198 10 false *4 1.604,2.417 1.917,2.615 0.313,0.198 10 false *3 5.438,2.417 5.75,2.615 0.313,0.198 10 false *3
*A for 2WD *B Upper Face
*C Lower Face - -
*1 REAR FLOOR PAN *2 SPARE WHEEL CLAMP BRACKET
*3 REAR FLOOR SIDE PANEL *4 ACTUATOR COVER BRACKET NO.3
*5 WELD BOLTS - -



b.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K162801C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for 2WD - -
K108837

Adhesive - -


K162806C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for 2WD - -


K162807C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for 2WD *B LH Side


K162808C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for 2WD *B RH Side



c.

Weld the wheelhouse inner gusset front to the vehicle side.

K159746C03
0.167,0.333 7,3.583 6.833,3.25 3.583,3.583 3.583,0.333 false 1.5,2.646 1.167,3.167 1.167,3.167 1.333,3.167 false 5.75,3.167 5.917,3.167 5.917,3.167 5.573,2.635 false 3.688,0.438 4,0.635 0.313,0.198 10 false *C 0.271,0.438 0.583,0.635 0.313,0.198 10 false *B 1.417,3.083 1.729,3.281 0.313,0.198 10 false *1 5.583,3.083 5.896,3.281 0.313,0.198 10 false *1 1.688,0.656 2,0.854 0.313,0.198 10 false *a 5.521,0.656 5.833,0.854 0.313,0.198 10 false *a 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for 2WD *B LH Side
*C RH Side - -
*1 WHEELHOUSE INNER GUSSET FRONT - -
*a 15 mm (0.59 in.) - -



d.

Before temporarily installing the new parts, weld the rear floor pan, voltage converter mount bracket lower front, voltage converter mount bracket lower rear, rear floor side panel, voltage converter mount bracket upper front and with the standard number of welding points.

K162813C01
0.667,0.25 6.5,6.583 5.833,6.333 0.667,3.5 6.5,3.5 false 2.594,0.875 2.333,0.5 2.333,0.5 2.167,0.5 false 4.167,3.167 4,3.167 4,3.167 3.448,2.083 false 4.292,4.927 5.083,4.583 5.083,4.583 5.25,4.583 false 5.083,4.583 4.281,4.99 false 3.667,6.417 3.5,6.417 3.5,6.417 3.583,5.646 false 3.5,6.417 4.198,5.698 false 3.5,6.417 2.948,5.688 false 3.385,1 3.75,0.5 3.75,0.5 3.917,0.5 false 1.917,5.583 2.083,5.583 2.083,5.583 2.75,5.146 false 5.167,3.25 5,3.25 5,3.25 4.833,2.833 false 2,3.25 2.167,3.25 2.167,3.25 2.333,2.833 false 5.083,4.583 4.031,4.865 false 0.771,0.354 1.083,0.552 0.313,0.198 10 false *B 0.771,3.604 1.083,3.802 0.313,0.198 10 false *C 2,0.438 2.313,0.635 0.313,0.198 10 false *1 4.219,3.083 4.531,3.281 0.313,0.198 10 false *3 5.333,4.5 5.646,4.698 0.313,0.198 10 false *6 3.75,6.333 4.063,6.531 0.313,0.198 10 false *6 3.969,0.417 4.281,0.615 0.313,0.198 10 false *2 1.729,5.51 2.042,5.708 0.313,0.198 10 false *5 5.25,3.167 5.563,3.365 0.313,0.198 10 false *4 1.771,3.167 2.083,3.365 0.313,0.198 10 false *4 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for AWD *B Upper Face
*C Lower Face - -
*1 REAR FLOOR PAN *2 VOLTAGE CONVERTER MOUNT BRACKET LOWER FRONT
*3 VOLTAGE CONVERTER MOUNT BRACKET LOWER REAR *4 REAR FLOOR SIDE PANEL
*5 VOLTAGE CONVERTER MOUNT BRACKET UPPER FRONT *6 WELD BOLTS



e.

Apply adhesive (3MTM AutomixTM Panel Bonding Adhesive #8115).

HINT:
·

Do not apply adhesive around the plug welding points.

·

Minimize squeeze out in plug welding areas.



K162809C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for AWD - -
K108837

Adhesive - -


K162814C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for AWD - -


K162815C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for AWD *B LH Side


K162816C01
0.104,0.104 0.417,0.302 0.313,0.198 10 false *A 0.104,0.313 0.417,0.51 0.313,0.198 10 false *B
*A for AWD *B RH Side



f.

Weld the wheelhouse inner gusset front to the vehicle side.

K162780C02
0.167,0.333 7,3.583 6.833,3.25 3.583,3.583 3.583,0.333 false 1.583,2.813 1.25,3.333 1.25,3.333 1.417,3.333 false 5.583,3.333 5.75,3.333 5.75,3.333 5.458,2.802 false 3.688,0.438 4,0.635 0.313,0.198 10 false *C 0.271,0.438 0.583,0.635 0.313,0.198 10 false *B 1.5,3.25 1.813,3.448 0.313,0.198 10 false *1 5.417,3.25 5.729,3.448 0.313,0.198 10 false *1 1.688,0.656 2,0.854 0.313,0.198 10 false *a 5.521,0.656 5.833,0.854 0.313,0.198 10 false *a 0.104,0.104 0.417,0.302 0.313,0.198 10 false *A
*A for AWD *B LH Side
*C RH Side - -
*1 CENTER FLOOR PANEL REINFORCEMENT SUB-ASSEMBLY - -
*a 15 mm (0.59 in.) - -



g.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting /coating)


h.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.