CONSTRUCTION
The brake control system consists of the linear solenoid valve (SLA, SLR), gap hold valve (SGH), stroke simulator cut valve (SSA), pressure holding solenoid valve (SFRH, SRLH, SRRH, SFLH), pressure reduction solenoid valve (SFRR, SRLR, SRRR, SFLR), etc., and controls the brake fluid pressure in each wheel cylinder.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
OPERATION
During Normal Operation
During normal braking, the stroke simulator cut valve (SSA) is closed and the gap hold valve (SGH) is open. The servo chamber pressure which is controlled by the linear solenoid valve according to the target wheel cylinder pressure is applied to the master cylinder chambers. By controlling the linear solenoid valves SLA and SLR, the brake fluid pressure of each wheel cylinder is increased, held or decreased.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| Normal Braking | ||||
|---|---|---|---|---|
| When Increasing Pressure | When Holding Pressure | When Decreasing Pressure | ||
| Linear Solenoid Valve | SLA | ON (Open) | OFF (Closed) | OFF (Closed) |
| SLR | ON (Closed) | ON (Closed) | OFF (Open) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | OFF (Open) | OFF (Open) |
| SRLH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SRRH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SFLH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SFRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SFLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
ABS and EBD
The ABS and EBD controls the pump, pressure holding solenoid valve and pressure reduction valve to control the brake fluid pressure of each wheel cylinder.
| *1 | Pressure Holding Solenoid Valve | *2 | Port 1 |
| *3 | Pressure Reduction Solenoid Valve | *4 | Port 2 |
| *a | Pressure Increase Mode | *b | Pressure Hold Mode |
| *c | Pressure Decrease Mode | *d | To Reservoir |
| *e | To Wheel Cylinder | - | - |
| When Not Operating | Normal Braking | - | - |
|---|---|---|---|
| When Operating | Pressure Increase Mode | Pressure Hold Mode | Pressure Decrease Mode |
| Pressure Holding Solenoid Valve | OFF | ON | ON |
| Pressure Reduction Solenoid Valve | OFF | OFF | ON |
| Port 1 | Open | Closed | Closed |
| Port 2 | Closed | Closed | Open |
| Wheel Cylinder Pressure | Apply Fluid Pressure | Hold Fluid Pressure | Release Fluid Pressure |
Brake Assist
When brake assist control is operating, pressure is supplied from the brake booster pump assembly to the master cylinder chambers via the servo chamber to apply brake fluid pressure higher than that of the depression force of the brake pedal to each wheel cylinder.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| When Brake Assist is not Operating | When Brake Assist is Operating | ||
|---|---|---|---|
| Linear Solenoid Valve | SLA | ON (Open) | ON (Open) |
| SLR | ON (Closed) | ON (Closed) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | OFF (Open) |
| SRLH | OFF (Open) | OFF (Open) | |
| SRRH | OFF (Open) | OFF (Open) | |
| SFLH | OFF (Open) | OFF (Open) | |
| SFRR | OFF (Closed) | OFF (Closed) | |
| SRLR | OFF (Closed) | OFF (Closed) | |
| SRRR | OFF (Closed) | OFF (Closed) | |
| SFLR | OFF (Closed) | OFF (Closed) | |
TRC
TRC pressurizes the master cylinder chambers due to servo pressure generated in the brake booster pump assembly, limits the drive force from the engine and controls each pressure holding solenoid valve and pressure reduction solenoid valve to apply more brake fluid pressure to the wheel cylinder of each drive wheel to reduce slippage.
The following illustration shows the operation during pressure increase mode.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| TRC Not Operating | TRC Operating | ||||
|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Hold Mode | Pressure Decrease Mode | |||
| Linear Solenoid Valve | SLA | OFF (Closed) | ON (Open) | ON (Open) | ON (Open) |
| SLR | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| SRLH | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | |
| SRRH | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | |
| SFLH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SFRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| SRLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SFLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
VSC
When the VSC system is operating, pressure is supplied from the brake booster pump assembly to the master cylinder chambers via the servo chamber to apply brake fluid pressure to each wheel cylinder to suppress front and rear wheel skidding.
Both of the following illustrations show the operation during pressure increase mode when the driver is not depressing the brake pedal while cornering to the right.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| VSC Not Operating | VSC Operating | ||||
|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Hold Mode | Pressure Decrease Mode | |||
| Linear Solenoid Valve | SLA | OFF (Closed) | ON (Open) | ON (Open) | ON (Open) |
| SLR | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| SRLH | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | |
| SRRH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SFLH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SFRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| SRLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| SFLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| VSC Not Operating | VSC Operating | ||||
|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Hold Mode | Pressure Decrease Mode | |||
| Linear Solenoid Valve | SLA | OFF (Closed) | ON (Open) | ON (Open) | ON (Open) |
| SLR | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) |
| SRLH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SRRH | OFF (Open) | ON (Closed) | ON (Closed) | ON (Closed) | |
| SFLH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SFRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| SRRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SFLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
Crosswind Assist (CWA)
When the Crosswind Assist (CWA) system is operating, pressure is supplied from the brake booster pump assembly to the master cylinder chambers via the servo chamber to apply brake fluid pressure to the wheel cylinders on the upwind side to suppress the yaw moment caused by the crosswind and the deviation of the vehicle.
The brake control of Crosswind Assist (CWA) is the same as that used by VSC to suppress oversteer.
Active Cornering Assist (ACA)
When the Active Cornering Assist (ACA) system is operating, pressure is supplied from the brake booster pump assembly to the master cylinder chambers via the servo chamber to apply brake fluid pressure to the wheel cylinders on the inner side of the turn to suppress understeer.
The brake control of Active Cornering Assist (ACA) is the same as that used by VSC to suppress understeer.
Hill-start Assist Control
After the driver operates the brakes, the pressure holding valve is closed to maintain a certain amount of the generated brake fluid pressure in each wheel cylinder to perform hill-start assist control.
The following illustration shows the operation during pressure hold mode.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| Hill-assist Control Not Operating | Hill-assist Control Operating | |||
|---|---|---|---|---|
| When Holding Pressure | When Decreasing Pressure | |||
| Linear Solenoid Valve | SLA | OFF (Closed) | OFF (Closed) | OFF (Closed) |
| SLR | OFF (Open) | ON (Closed) | OFF (Open) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | OFF (Open) | OFF (Open) |
| SRLH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SRRH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SFLH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SFRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SFLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
Brake Hold
The operation of the solenoid valves under the brake hold is the same as the operation of the hill-start assist control.
Steering Cooperative Control Operation
The operation of the solenoid valves under the steering cooperative control is the same as the TRC or VSC operation.
Downhill Assist Control
Based on the information provided by various sensors, switches and the ECM, the skid control ECU determines the conditions that enable the downhill assist control operation. Then, the skid control ECU controls the fluid pressure that is generated by the pump and applies it by way of the solenoid valve to the brake wheel cylinder of each wheel in the following 3 modes: pressure reduction, pressure holding and pressure increase modes.
The skid control ECU computes the vehicle speed, travel direction and the gradient of the hill in accordance with the signals that are input by the speed sensor and the yaw rate and deceleration sensor, and performs brake control to attain the target vehicle speed. The target vehicle speed is determined by the direction of the vehicle.
| Travel Direction | Target Vehicle Speed |
|---|---|
| Forward | 5 km/h to 7 km/h (3 mph to 4 mph) |
| Backward | 3 km/h to 5 km/h (2 mph to 3 mph) |
During the downhill assist control operation, the skid control ECU outputs signals to the stop light switch assembly to cause the stop light to turn on and to the combination meter assembly to cause the slip indicator light to blink.
The following illustration shows the operation during pressure increase mode.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| TRC Not Operating | TRC Operating | ||||
|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Hold Mode | Pressure Decrease Mode | |||
| Linear Solenoid Valve | SLA | ON (Open) | ON (Open) | OFF (Closed) | OFF (Closed) |
| SLR | ON (Closed) | ON (Closed) | ON (Closed) | OFF (Open) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) |
| SRLH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SRRH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SFLH | OFF (Open) | OFF (Open) | ON (Closed) | ON (Closed) | |
| SFRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| SRLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| SRRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
| SFLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | ON (Open) | |
Hydraulic Booster Mode (Operation when The Brake Actuator Stops)
When the brake actuator stops due to failure, the stroke simulator cut valve (SSA) is opened and the gap hold valve (SGH) is closed. This applies the fluid pressure generated in the master cylinder chambers to each wheel cylinder.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| Hydraulic Booster Mode Operating | ||
|---|---|---|
| Linear Solenoid Valve | SLA | OFF (Closed) |
| SLR | OFF (Open) | |
| Switching Solenoid Valve | SSA | OFF (Open) |
| SGH | OFF (Closed) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) |
| SRLH | OFF (Open) | |
| SRRH | OFF (Open) | |
| SFLH | OFF (Open) | |
| SFRR | OFF (Closed) | |
| SRLR | OFF (Closed) | |
| SRRR | OFF (Closed) | |
| SFLR | OFF (Closed) | |
Operation when One Circuit is Malfunctioning
The stroke simulator cut valve (SSA) is closed and gap hold valve (SGH) is opened. Pressure is supplied from the brake booster pump assembly to the master cylinder chambers via the servo chamber to apply the brake fluid pressure to each normal wheel cylinder to provide braking in one circuit.
The following illustration shows the operation during pressure increase mode.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| Control Operation during One Circuit Malfunction | ||||
|---|---|---|---|---|
| When Increasing Pressure | When Holding Pressure | When Decreasing Pressure | ||
| Linear Solenoid Valve | SLA | ON (Open) | OFF (Closed) | OFF (Closed) |
| SLR | ON (Closed) | ON (Closed) | OFF (Open) | |
| Switching Solenoid Valve | SSA | ON (Closed) | ON (Closed) | ON (Closed) |
| SGH | ON (Open) | ON (Open) | ON (Open) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) | OFF (Open) | OFF (Open) |
| SRLH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SRRH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SFLH | OFF (Open) | OFF (Open) | OFF (Open) | |
| SFRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SRRR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
| SFLR | OFF (Closed) | OFF (Closed) | OFF (Closed) | |
Operation during Power Supply Malfunction
The stroke simulator cut valve (SSA) is opened and gap hold valve (SGH) is closed. With this, pressure generated in the master cylinder chambers by the depression of the brake pedal by the driver is applied to each wheel cylinder.
| *1 | Brake Master Cylinder Reservoir Assembly | *2 | Brake Booster Pump Assembly |
| *3 | Accumulator | *4 | Pump Motor |
| *5 | Master Cylinder | *6 | Brake Pedal Stroke Sensor Assembly |
| *7 | Brake Actuator | *8 | Relief Valve |
| *9 | Accumulator Pressure Sensor (Pacc) | *10 | Servo Pressure Sensor (Psrv) |
| *11 | Regulator | *12 | Linear Solenoid Valve (SLA) |
| *13 | Linear Solenoid Valve (SLR) | *14 | Stroke Simulator Cut Valve (SSA) |
| *15 | Gap Hold Valve (SGH) | *16 | Stroke Simulator Pressure Sensor (Prct) |
| *17 | Stroke Simulator | *18 | Brake Actuator Assembly |
| *19 | Pressure Holding Solenoid Valve (SFRH) | *20 | Pressure Holding Solenoid Valve (SRLH) |
| *21 | Pressure Holding Solenoid Valve (SRRH) | *22 | Pressure Holding Solenoid Valve (SFLH) |
| *23 | Pressure Reduction Solenoid Valve (SFRR) | *24 | Pressure Reduction Solenoid Valve (SRLR) |
| *25 | Pressure Reduction Solenoid Valve (SRRR) | *26 | Pressure Reduction Solenoid Valve (SFLR) |
| *27 | Pump | *28 | Reservoir |
| *29 | Front Brake RH | *30 | Rear Brake LH |
| *31 | Rear Brake RH | *32 | Front Brake LH |
| Control Operation during Power Supply Malfunction | ||
|---|---|---|
| Linear Solenoid Valve | SLA | OFF (Closed) |
| SLR | OFF (Open) | |
| Switching Solenoid Valve | SSA | OFF (Open) |
| SGH | OFF (Closed) | |
| Controlling Solenoid Valve | SFRH | OFF (Open) |
| SRLH | OFF (Open) | |
| SRRH | OFF (Open) | |
| SFLH | OFF (Open) | |
| SFRR | OFF (Closed) | |
| SRLR | OFF (Closed) | |
| SRRR | OFF (Closed) | |
| SFLR | OFF (Closed) | |