Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › ADAPTIVE HIGH BEAM SYSTEM › from 2021.07
NM3700E _95 ADAS / AD _095506 ADVANCED DRIVER ASSISTANCE SYSTEM _0487032 ADAPTIVE HIGH BEAM SYSTEM CO CONTROL F

ADVANCED DRIVER ASSISTANCE SYSTEM  ADAPTIVE HIGH BEAM SYSTEM  CONTROL  ADAPTIVE HIGH BEAM SYSTEM (AHS) CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Headlight Assembly RH Headlight ECU Sub-assembly RH Sends adaptive high beam system control request signals to the light control LED ECU RH.
Light Control LED ECU RH Receives signals from the headlight ECU sub-assembly RH and controls the headlight illumination based on the conditions of the vehicle and surroundings.
Headlight Assembly LH Headlight ECU Sub-assembly LH Sends adaptive high beam system control request signals to the light control LED ECU LH.
Light Control LED ECU LH Receives signals from the headlight ECU sub-assembly LH and controls the headlight illumination based on the conditions of the vehicle and surroundings.
Main Body ECU (Multiplex Network Body ECU) Controls the headlight ECU sub-assembly LH and headlight ECU sub-assembly RH based on signals from various sensors and switches.
Forward Recognition Camera
·

Captures an image of the area in front of the vehicle and uses the image to determine the position of preceding and oncoming vehicles and to determine the brightness of the surrounding area. This data is then sent to the headlight ECU sub-assembly LH via CAN communication.

·

Controls the supply of electric current to the camera heater when the ambient temperature is low.


Camera Heater (Forward Recognition Hood with Heater Sub-assembly) Control is performed by the forward recognition camera to supply electric current and heat the heater, preventing the windshield glass in front of the forward recognition camera from fogging up.
Millimeter Wave Radar Sensor Assembly Detect the presence of a vehicle traveling ahead, the vehicle-to-vehicle distance and sends the signal to the forward recognition camera.
Height Control Sensor Detects the height of the vehicle and sends the signal to the headlight ECU sub-assembly LH.
Airbag Sensor Assembly Detects the yaw rate of the vehicle and transmits the signal to the headlight ECU sub-assembly LH.
Steering Sensor
·

Detects the angle of steering and transmits a signal to the headlight ECU sub-assembly LH.

·

Sends the light control switch and dimmer switch signals to the main body ECU.


Turn Signal Switch Light Control Switch Sends the light control switch signals to the steering sensor.
Dimmer Switch Sends the dimmer switch signals to the steering sensor.
Auto High Beam Switch Sends the auto high beam switch signals to the main body ECU.
Automatic Light Control Sensor Detects the ambient light level and transmits a signal to the main body ECU.
Combination Meter Assembly
·

Receives the vehicle speed signal from the skid control ECU and sends the signal to the main body ECU.

·

Receives illumination request signals for the indicator from the main body ECU and illuminates/turns off the indicator.

·

When a warning request signal is received from the main body ECU, the master warning is turned on and the buzzer sounds, and the warning is displayed on the multi-information display.


Brake Actuator Assembly Skid Control ECU Sends the vehicle speed signal to the combination meter assembly.
Central Gateway ECU (Network Gateway ECU) Relays the signal between the CAN communication lines.


SYSTEM CONTROL


a.

Operation Conditions of the Adaptive High Beam System

i.

The adaptive high beam system operates when all of the following conditions are met. While the adaptive high beam system is on, the adaptive high beam indicator light illuminates.

·

The ignition switch is ON.

·

The light control switch is in the HEAD position or AUTO position and the headlights are operating.

·

The dimmer switch is in the LO position.

·

The auto high beam switch is on.

·

The vehicle speed is approximately 15 km/h (9 mph) or more.




b.

High Beam Light Distribution Control Function

i.

In high beam light distribution control function, the light control LED ECU controls the brightness and illumination area of the high beam.


ii.

The high beam light distribution control function changes the intensity and illumination area according to 3 vehicle speed ranges:

Illumination Mode Description of Function Vehicle Speed
Low Speed Mode (Town Mode)
·

Widens the illuminated area.

·

The brightness of the headlights is adjusted to ensure that pedestrians are visible while not being dazzled.

·

Reduces illumination of the side of the road.


15 - 30 km/h (9 - 19 mph)
Normal Mode
·

At medium speeds, the illuminated area in front of the vehicle is extended and necessary areas to the left and right of the vehicle are illuminated.

·

Reduces the light distribution at the center of the high beams when driving in rainy weather to prevent glare to oncoming vehicles caused by camera recognition delays.


30 - 120 km/h (19 - 75 mph)
High Speed Mode
·

The illuminated area in front of the vehicle is narrowed.

·

Adjusts the high beams to ensure visibility far in front of the vehicle.

·

Reduces the light distribution at the center of the high beams when driving in rainy weather to prevent glare to oncoming vehicles caused by camera recognition delays.


120 km/h (75 mph) or more

Low Speed Mode (Town Mode)
Y189250C01
3.719,1.26 3.521,0.313 3.521,0.313 2.615,0.313 true 3.979,2.479 4.24,3.604 4.24,3.604 4.875,3.604 true 2.448,0.229 2.719,0.479 0.271,0.25 10 false *a 4.979,3.51 5.25,3.698 0.271,0.188 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams


Normal Mode
Y189251C03
5.833,3.344 5.333,3.344 5.333,3.344 5.135,2.563 true 2.99,0.563 3.5,0.563 3.5,0.563 3.646,1.229 true 2.813,0.479 3.073,0.698 0.26,0.219 10 false *a 5.906,3.271 6.219,3.427 0.313,0.156 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams


High Speed Mode
Y189252C03
3.625,1.229 3.76,0.458 3.76,0.458 4.219,0.458 true 3.646,2.51 3.438,3.573 3.438,3.573 2.698,3.573 true 4.281,0.396 4.594,0.604 0.313,0.208 10 false *a 2.531,3.51 2.844,3.667 0.313,0.156 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams




c.

Light Disable Control Function

i.

The light disable control function dims LEDs in the high beam headlight accordingly when the forward recognition camera detects a preceding vehicle or an oncoming vehicle.


ii.

The light control LED ECU and LED unit enable the LEDs of the headlight assembly to be dimmed independently as necessary.

Y189253C03
4.906,2.854 5.208,2.854 5.208,2.854 5.323,2.271 true 0.896,1 1.229,1 1.229,1 1.292,1.344 true 0.885,0.729 1.854,0.729 1.854,0.729 1.958,1.302 true 3.115,0.781 2.885,0.781 2.885,0.781 2.813,1.302 true 1.292,2.99 1.594,2.99 1.594,2.99 1.708,2.406 true 4.313,0.958 4.448,0.958 4.448,0.958 4.51,1.302 true 4.292,0.74 5.042,0.74 5.042,0.74 5.188,1.333 true 6.698,0.948 6.552,0.948 6.552,0.948 6.5,1.271 true 0.292,0.615 0.604,0.802 0.313,0.188 10 false *A 3.792,0.583 4.104,0.74 0.313,0.156 10 false *B 4.719,2.781 5,2.969 0.281,0.188 10 false *b 0.729,0.646 0.958,0.844 0.229,0.198 10 false *a 0.729,0.927 0.99,1.115 0.26,0.188 10 false *a 3.156,0.698 3.417,0.885 0.26,0.188 10 false *a 1.104,2.917 1.385,3.104 0.281,0.188 10 false *b 4.146,0.667 4.406,0.854 0.26,0.188 10 false *a 6.729,0.865 6.99,1.063 0.26,0.198 10 false *a 4.156,0.875 4.417,1.063 0.26,0.188 10 false *a
*A When driving on road with one lane in each direction *B When driving on a multi-lane road
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams




d.

Headlight Swivel Control Function

i.

The headlight swivel control function adjusts the brightness of headlights while turning a corner to ensure excellent visibility.

Y189254C03
1.781,1.646 1.719,1.063 1.719,1.063 1.021,1.063 true 1.781,2.396 1.708,3.063 1.708,3.063 0.979,3.063 true 6.208,1.656 6.302,1.063 6.302,1.063 6.656,1.063 true 6.031,2.281 6.135,2.969 6.135,2.969 6.625,2.969 true 0.813,0.979 1.125,1.135 0.313,0.156 10 false *a 0.823,2.979 1.094,3.208 0.271,0.229 10 false *b 6.729,0.99 6.948,1.198 0.219,0.208 10 false *a 6.667,2.896 6.938,3.125 0.271,0.229 10 false *b
*a Area Illuminated by High Beams *b Area Illuminated by Low Beams




e.

Cut-off Line Tilt Control Function

i.

The cut-off line tilt function controls the leveling motor built into the headlight assembly to optimize the illumination area of the low beams in accordance with the distance to the preceding vehicle detected by the forward recognition camera.

Y189255C01
1.917,0.896 2.531,0.896 2.531,0.896 2.833,1.906 true 5.396,2.771 4.521,2.771 4.521,2.771 4.24,1.844 true 1.219,5.24 1.719,5.24 1.719,5.24 1.781,4.792 true 4.708,5.24 5.146,5.24 5.146,5.24 5.229,4.844 true 6.188,3.875 5.677,3.875 5.677,3.875 5.552,4.573 true 1.729,0.813 2.031,1.021 0.302,0.208 10 false *a 5.448,2.719 5.781,3 0.333,0.281 10 false *b 1.052,5.156 1.354,5.365 0.302,0.208 10 false *a 4.531,5.177 4.833,5.385 0.302,0.208 10 false *a 6.229,3.802 6.563,4.083 0.333,0.281 10 false *b
*a Illumination Area of Low Beams without Control *b Illumination Area of Low Beams during Control





FUNCTION


a.

The adaptive high beam system operates when the auto high beam switch is on, the light control switch is in the HEAD or AUTO position and the dimmer switch is set to LO. The adaptive high beam system uses the forward recognition camera to detect the lights of oncoming vehicles and the taillights of preceding vehicles and to determine the brightness of the surrounding area in order to select which LEDs of the LED array to illuminate.


b.

The headlight ECU sub-assemblies control the adaptive high beam system.


c.

When the adaptive high beam system is on, the adaptive high beam indicator light in the combination meter assembly illuminates.



FAIL-SAFE


a.

If the headlight ECU sub-assembly LH detects a system malfunction, the ECU performs fail-safe control. For details, refer to the Repair Manual.


b.

Combination Meter Assembly

i.

If a malfunction occurs in the adaptive high beam system (AHS), the master warning indicator illuminates, the buzzer sounds, and the message "Headlight System Malfunction Visit Your Dealer" is displayed in the multi-information display.




DIAGNOSIS


a.

To make diagnosing the system easier, a diagnosis function is provided for enhanced serviceability. Connecting a diagnostic tool allows DTCs for malfunctioning areas to be read and configurable settings for functions to be changed.