OUTLINE
A panoramic view monitor system is provided which displays a panoramic view of the vehicle to assist the driver during parking and low speed driving. The panoramic image is created by seamlessly combining images from each of the wide-angle, high-resolution television camera assemblies installed to the front, rear, left and right sides of the vehicle into a composite overhead* view and displays it on the multi-display screen.
* The overhead view shows a view simulating a perspective looking down from high above the vehicle. It shows the entire surroundings as they might appear when looking down from above.
The panoramic view monitor system provides a variety of image display modes to make confirming the area around the vehicle possible according to driving conditions. These display modes include the simultaneous display of the panoramic view and the front view (Front View) or rear view (Rear View and Wide Rear View), or the front side of the vehicle as seen looking down from the rear (Clearance View).
"Side View and Front View", "Side View and Rear View" and "Dual Side View" have been provided. This enables the surroundings of the vehicle to be checked for safety even with the outer rear view mirrors in a folded state, which can be useful when parking the vehicle in a narrow space.
The TOYOTA parking assist-sensor system-linked function has been adopted. When the TOYOTA parking assist-sensor system detects an obstacle while driving at low speed, the monitor screen automatically displays the panoramic view and front view. Furthermore, an enlargement function has been provided that displays an enlarged view of the left and right corners in the travel direction (forward or backward) of the vehicle.
Do not rely solely upon the panoramic view monitor system. As with unequipped models, drive carefully while directly confirming the safety of your surroundings.
| *a | The illustration shown is an example only. The illustration may differ from the actual vehicle screen. | - | - |
| Screen Display | Shift Position | Notes | |
|---|---|---|---|
| See-through View Mode |
|
P | Provides a subjective view of the vehicle surroundings when parked. |
| Moving View Mode |
|
P | Provides an objective view of the vehicle surroundings when parked. |
| Panoramic View and Front View Mode |
|
Except P | Used to check the conditions around and in front of the vehicle when driving at low speed. |
| Panoramic View and Clearance View Mode |
|
Except P or R | Used to check the conditions around, in front of, and to the sides of the vehicle when driving at low speed. |
| Panoramic View and Rear View Mode |
|
R | Used to check the conditions around and behind the vehicle when driving at low speed. |
| Rear View Mode |
|
R | Used to check the conditions behind the vehicle. |
| Wide Rear View Mode |
|
R | Used to check the conditions behind the vehicle. |
| Side View and Front View Mode |
|
Except P or R | When the door mirrors are folded, this is used to check the conditions to the sides and in front of the vehicle. |
| Side View and Rear View Mode |
|
R | When the door mirrors are folded, this is used to check the conditions to the sides of and behind the vehicle. |
| Dual Side View Mode |
|
Except P or R | When the door mirrors are folded, this is used to check the conditions to the sides of the vehicle. |
MAIN FEATURES
The panoramic view monitor system seamlessly combines images from the front, rear, left and right television camera assemblies and displays the combined images as the panoramic view image. Also, the system assists the driver to confirm the area around the vehicle while driving at low speeds and when parking by simultaneously displaying the panoramic view and front (front view), rear (rear view and wide rear view), or the front side of the vehicle as seen looking down from the rear (clearance view) images on the multi-display.
The front image of the vehicle (front view) assists the driver to confirm safety at locations with poor visibility, such as intersections and T-junctions, and the area in front of the vehicle when starting off.
The rear images (rear view and wide rear view) assist with driving in reverse.
The images of the front side of the vehicle as seen looking down from the rear (clearance view) assist with confirming the safety of the area to the sides of the vehicle, evading obstacles and driving close to the shoulders on narrow roads.
When the door mirrors are folded, the side images (dual side view) assist with confirming the safety of the area to the sides of the vehicle, evading obstacles and driving close to the shoulders on narrow roads.
Do not rely solely upon the panoramic view monitor system. As with unequipped models, drive carefully while directly confirming the safety of your surroundings.
See-through view and moving view combine images from the front, rear, left and right television camera assemblies to create a simulated view of the space surrounding the vehicle, reducing the blind spots from inside the vehicle to assist with confirming the safety of the area surrounding the vehicle. (Can only be displayed when the TOYOTA parking assist-sensor system is ON)
| *a | See-through View Mode | *b | Moving View Mode |
PRECAUTION
When driving the vehicle, be sure to check for safety by directly observing the area behind the vehicle as well as the vehicle surroundings. Failing to observe these precautions could lead to unexpected accidents such as collisions with other vehicles, etc. When using the panoramic view monitor system, be sure to observe the following precautions.
Do not rely solely upon the panoramic view monitor system. As with unequipped models, drive carefully while directly confirming the safety of the area behind the vehicle and the vehicle surroundings.
Do not drive while only viewing the monitor screen. The image displayed on the monitor screen may differ from actual conditions. Also, since the area captured by each television camera is limited, do not attempt to maneuver the vehicle while only viewing the monitor screen. Doing so could lead to unexpected accidents such as collisions with other vehicles, etc. Always drive carefully while directly confirming the safety of the area behind the vehicle and the vehicle surroundings by observing them directly and using the vehicle mirrors, etc.
When driving with the system in operation, drive carefully while depressing the brake pedal to control the vehicle speed.
Do not use the panoramic view monitor system under the following conditions:
The road surface is slippery (frozen or covered with snow).
Snow chains or an emergency spare tire are being used.
The vehicle is driven on a road that is not level, such as a slope.
The front or back doors are not fully closed.
Tires other than the manufacturer specified ones are being used.
The suspension has been modified.
When the outside air temperature is low, the screen may become darker or appear faint. Since moving objects in particular may become distorted or disappear, always drive carefully while directly confirming the safety of your surroundings.
When tires are replaced, the position indicated by the guide lines displayed on the screen may differ slightly.
About panoramic view monitor system video:
See-through view, moving view, panoramic view and clearance view video imagery is created by using image processing to combine the images from the front, rear, left and right television camera assemblies. As the displayable area and display contents have certain limitations, it is important to understand the particular characteristics of the panoramic view monitor system when using it.
In see-through view, moving view, panoramic view and clearance view, there are regions at the four corners where the fields of view of the various cameras intersect. The image composition processing that is centered around these areas can result in reduced image clarity, but this is not a malfunction.
Depending on the ambient illumination conditions around the various cameras, see-through view, moving view, panoramic view and clearance view may appear lighter or darker.
See-through view, moving view, panoramic view and clearance view do not display anything above or outside the range of each television camera assembly.
There are blind spots near the vehicle, resulting in areas that cannot be displayed by the panoramic view monitor system.
Objects displayed in the front view, rear view, wide rear view and dual side view modes may not be displayed in the see-through view, moving view, panoramic view and clearance view modes.
The panoramic view monitor system may display objects such as people and obstacles in a way that may differ from the actual conditions. (Objects or persons may appear to have fallen down, or may disappear or suddenly appear near the areas where the imagery from different cameras is joined, or may seem to be at different locations or distances than in reality, etc.)
If a back door or the left/right front doors are open, the panoramic view monitor system will not be displayed correctly.
Since the vehicle icon displayed in the see-through view, moving view, panoramic view and clearance view modes is displayed using computer graphics, the vehicle color, shape and size may differ from the actual vehicle. For this reason, objects close to the vehicle may appear to be approaching or to be located in relative positions that differ from their real positions relative to the vehicle.
About the area displayed on the screen:
See-through view, moving view, panoramic view and clearance view modes
There are blind spots near the vehicle, resulting in areas that cannot be displayed. Even if the screen shows nothing in the vicinity of the vehicle, it is possible that there could be an obstacle in the movement path that the vehicle could collide with. Be sure to directly confirm the safety of your surroundings.
The see-through view, moving view, panoramic view and clearance view modes display a composite image from the 4 television cameras that is processed based on the assumption that the road surface is level, so the following display situations may occur:
Standing objects may appear to have fallen down and be long and thin, or may appear to be large.
Objects positioned higher than the road surface may appear to be farther away than they really are, or may not be visible.
Objects with vertical height may seem to suddenly appear from the region where the camera imagery is joined.
Depending on lighting conditions, the brightness of the television camera display imagery may be uneven.
Changes in the vehicle height or tilt due to the number of passengers, load capacity, amount of fuel remaining, etc. could alter the alignment of the displayed image.
If the doors are not fully closed, the images and guide lines may not be displayed correctly.
| *a | See-through View | *b | Moving View |
| *c | Clearance View | *d | Panoramic View |
| *e | Obstacle in blind spot area | *f | Illustration shows a representative example. The illustration may differ from the actual vehicle screen. |
|
Blind spot area not displayed on screen | - | - |
| *a | See-through View | *b | Moving View |
| *c | Clearance View | *d | Panoramic View |
| *e | Obstacle in blind spot area | *f | Illustration shows a representative example. The illustration may differ from the actual vehicle screen. |
| *a | Area where images are joined | - | - |
Front view, dual side view, side view, rear view and wide rear view modes
Depending on the vehicle and road conditions, the area displayed may differ.
The area covered by the television camera assembly is limited. The television camera assembly does not show objects close to either corner of the bumper or in the area directly under the bumper.
The apparent distances shown on the monitor will differ from actual distances.
Since each television camera assembly is equipped with a special lens, the distance displayed on the monitor differs from actual conditions.
| *a | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
|
Obstacle that cannot be seen | - | - |
| *a | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
| *a | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
| *a | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
|
Obstacle that cannot be seen | - | - |
| *a | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
|
Obstacle that cannot be seen | - | - |
Precautions for Television Camera
Observe the following precautions to prevent malfunction of the panoramic view monitor system:
Do not hit the television camera assemblies, or allow objects to strike them, or otherwise subject them to strong impacts. Doing so could cause the camera position to shift or cause the camera angle to become misaligned.
The camera uses a waterproof construction. Do not remove, disassemble, or modify the camera.
When washing a camera lens, first use a large amount of water to wash the dirt off the camera, then wipe the camera lens with a soft, damp cloth. Do not strongly rub the television camera assembly lenses. The lens may become damaged and unable to capture clear images.
The camera covers are made of resin. Do not allow organic solvent, wax, oil film remover, glass coating, etc. to contact the lens cover. If contact occurs, immediately wipe it off with a soft cloth and wash with water.
Do not subject the camera to sudden temperature changes, such as by pouring hot water on it in cold weather.
The side television camera assemblies incorporate infrared illuminators, and the side cameras can detect infrared light. For this reason, the infrared spectrum portion of light sources such as sunlight and halogen lights, as well as reflections from the infrared illuminators, may cause the coloration of the camera image to become faint or to have a tint that differs from that when the scene is viewed with visible light only.
If a camera has been subjected to a strong impact, it could experience problems such as a malfunction. In this case, contact your Toyota dealer as soon as possible.
If a camera has foreign matter such as water drops, snow, or dirt on it, it may not be able to capture a clear image. If this occurs, first use a large amount of water to wash the dirt off the camera, then wipe the camera lens with a soft, damp cloth.
Precautions for differences between screen display and actual road conditions
The composite image and guide lines displayed by the panoramic view monitor system use distance estimates assuming a flat road surface. For this reason, in the following conditions, disparity may occur between the display indication and the actual distance on the road surface. Operate the vehicle carefully.
| *a | Steep uphill incline behind vehicle | *b | Steep downhill incline behind vehicle |
| *c | Vehicle posture changed by passengers and load | *d | Disparity |
If a steep uphill incline is behind the vehicle, an obstacle will appear to be further away than it actually is, as shown in the illustration below.
| *a | Condition of this vehicle | *b | Appears to be in the same position |
| *c | Monitor display in situation A | *d | Monitor display in situation B |
| *e | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
Precautions for differences between screen display and actual 3-dimensional objects
The guide lines on the monitor screen are applicable for flat objects (such as the road surface). When projecting 3-dimensional objects (obstacles such as the cargo bed of a truck) or objects higher than the road surface (such as a vehicle bumper) are nearby, be sure to directly check the surroundings for safety.
As the predicted vehicle paths in panoramic view and clearance view are shown based on a flat road surface, when there are 3-dimensional objects higher than the road surface (vehicle bumpers, projecting walls or truck cargo beds, etc.) they may not appear on the monitor screen, or position judgment may not be possible. Even if it appears that a 3-dimensional object is outside the predicted path of the vehicle and will not be contacted, the object may in fact be in the path of the vehicle and your vehicle may come into contact with it.
| *a | Condition of this vehicle | *b | Monitor display |
| *c | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
| *a | Condition of this vehicle | *b | Monitor display |
| *c | Projecting portion | *d | Illustration shows a representative example. The illustration may differ from the actual vehicle screen |
As the predicted vehicle paths in rear view and wide rear view are shown based on the road surface, the positions of 3-dimensional objects cannot be predicted, On the monitor screen, even if it appears that the cargo bed of the truck is outside the predicted path of the vehicle and will not be contacted, the cargo bed is in fact be projecting over and into the path of this vehicle, and so this vehicle may come into contact with it.
| *a | Condition of this vehicle | *b | Monitor display |
| *c | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
As estimated distance lines in panoramic view, rear view and wide rear view are shown based on the road surface, the distances to 3-dimensional objects cannot be predicted, On the screen, the estimated distance lines make it appear that the truck is parked at position B, but in reality if this vehicle backs up to position A, this vehicle will come into contact with the truck. On the screen, the points appear to be located in the order A, B and C, but in reality points A and C are located at an equal distance from this vehicle, while point B is farther away.
| *a | Condition of this vehicle | *b | Monitor display |
| *c | Illustration shows a representative example. The illustration may differ from the actual vehicle screen | - | - |
Icon display
The icons of the TOYOTA parking assist-sensor system and RCTA function are displayed superimposed on a view captured by the camera. The icons may difficult to see depending on the brightness and color of the surroundings.
| *a | TOYOTA Parking Assist-sensor System Icon | *b | RCTA Icon |