Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door)
RM3700E _59 Vehicle Exterior _092998 WINDOW / GLASS _0438345 POWER WINDOW REGULATOR MOTOR(for Rear Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Rear Door)  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal M4-2 (B) or N4-2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



PROCEDURE

Hide 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.

Connect a positive (+) auxiliary battery lead to connector terminal M4-2 (B).

B572403C02
2.406,0.677 2.719,0.854 0.313,0.177 4.302,1.823 4.969,1.823 true 2.667,1.333 3.083,1.333 true 2,1.333 2.417,1.333 true 2.073,1.979 2.375,1.656 true 2.74,1.635 3.031,1.969 true 1.615,0.531 1.927,0.688 0.313,0.156 10 false *a 4.104,1.75 4.417,1.906 0.313,0.156 10 false *b 3.146,1.26 3.458,1.417 0.313,0.156 10 false GND 1.844,1.25 2.156,1.406 0.313,0.156 10 false B 3.042,1.979 3.604,2.26 0.563,0.281 10 false DOWN 1.927,1.99 2.365,2.188 0.438,0.198 10 false UP 2.469,0.698 2.781,0.896 0.313,0.198 10 false M4
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal M4-2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals M4-1 (GND) and M4-7 (DOWN) or M4-10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal M4-2 (B), connect a negative (-) auxiliary battery lead to terminal M4-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals M4-2 (B) and M4-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal M4-10 (UP).


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal M4-2 (B), connect a negative (-) auxiliary battery lead to terminal M4-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals M4-2 (B) and M4-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal M4-7 (DOWN).


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly RH.



Hide 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

Connect a positive (+) auxiliary battery lead to connector terminal N4-2 (B).

B572404C02
4.708,0.635 5.073,0.823 0.365,0.188 2.677,1.833 3.344,1.833 true 4.323,1.333 4.74,1.333 true 5,1.333 5.417,1.333 true 5.052,1.625 5.271,1.906 true 4.479,1.917 4.688,1.646 true 3.969,0.542 4.281,0.698 0.313,0.156 10 false *a 3.396,1.76 3.708,1.917 0.313,0.156 10 false *b 5.271,1.906 5.896,2.156 0.625,0.25 10 false DOWN 4.323,1.927 4.938,2.125 0.615,0.198 10 false UP 5.469,1.26 6.083,1.458 0.615,0.198 10 false GND 4.188,1.271 4.406,1.469 0.219,0.198 10 false B 4.802,0.656 5.417,0.854 0.615,0.198 10 false N4
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal N4-2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals N4-1 (GND) and N4-7 (DOWN) or N4-10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal N4-2 (B), connect a negative (-) auxiliary battery lead to terminal N4-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals N4-2 (B) and N4-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal N4-10 (UP).


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal N4-2 (B), connect a negative (-) auxiliary battery lead to terminal N4-1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals N4-2 (B) and N4-1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal N4-7 (DOWN).


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly LH.