84870A
1.INSTALL OUTER MIRROR SWITCH ASSEMBLY
Check the mirror select and surface adjust switch.
| *a | Mirror Select and Surface Adjust Switch |
| *b | Retractable Outer Mirror Switch |
| *c | Component without harness connected
(Outer Mirror Switch Assembly) |
Turn the mirror select and surface adjust switch to the L position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=6,2,7,11,4 |
||
| K12-6 (B) - K12-2 (VL) | Up | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Up | Below 1 Ω |
| K12-6 (B) - K12-2 (VL) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Down | Below 1 Ω |
| K12-7 (E) - K12-2 (VL) | Down | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-2 (VL) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-4 (HL) | Left | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Left | Below 1 Ω |
| K12-6 (B) - K12-4 (HL) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Right | Below 1 Ω |
| K12-7 (E) - K12-4 (HL) | Right | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-4 (HL) | Off | 10 kΩ or higher |
Turn the mirror select and surface adjust switch to the R position.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=6,5,7,11,3 |
||
| K12-6 (B) - K12-5 (VR) | Up | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Up | Below 1 Ω |
| K12-6 (B) - K12-5 (VR) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Down | Below 1 Ω |
| K12-7 (E) - K12-5 (VR) | Down | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-5 (VR) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-3 (HR) | Left | Below 1 Ω |
| K12-7 (E) - K12-11 (M+) | Left | Below 1 Ω |
| K12-6 (B) - K12-3 (HR) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-6 (B) - K12-11 (M+) | Right | Below 1 Ω |
| K12-7 (E) - K12-3 (HR) | Right | Below 1 Ω |
| K12-6 (B) - K12-11 (M+) | Off | 10 kΩ or higher |
| K12-7 (E) - K12-3 (HR) | Off | 10 kΩ or higher |
Check the mirror retract switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=9,8,10 |
||
| K12-9 (MAT) - K12-8 (E) | AUTO position | Below 1 Ω |
| K12-9 (MAT) - K12-8 (E) | Except AUTO position | 10 kΩ or higher |
| K12-10 (MR) - K12-8 (E) | Retract position | Below 1 Ω |
| K12-10 (MR) - K12-8 (E) | Except retract position | 10 kΩ or higher |
If the result is not as specified, replace the outer mirror switch assembly.
Check that the LED illuminates.
| *a | Component without harness connected
(Outer Mirror Switch Assembly) |
Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.
| Tester Connection | Specified Condition |
|---|---|
|
Click Location & Routing(K12)Location & Routingewd_type=routing;type=c;code=K12 Click Connector(K12)Body>Front Door Wire RH / Television Camera Wire>Outer Mirror Switch Assemblyewd_type=component;type=c;code=K12;pinno=12,1 |
|
| K12-12 (ILL+) - Auxiliary battery positive (+)
K12-1 (ILL-) - Auxiliary battery negative (-) |
LED illuminates |
If the result is not as specified, replace the outer mirror switch assembly.