Home › Vehicle Interior › HEATING / AIR CONDITIONING › AMBIENT TEMPERATURE SENSOR
RM3700E _58 Vehicle Interior _093020 HEATING / AIR CONDITIONING _0438497 AMBIENT TEMPERATURE SENSOR G

HEATING / AIR CONDITIONING  AMBIENT TEMPERATURE SENSOR  INSPECTION  


PROCEDURE

Hide 88790B 1.INSPECT THERMISTOR ASSEMBLY

a.

Check the resistance.

i.
B380459C50
2.344,0.167 2.677,0.333 0.333,0.167 0.167,0.885 0.365,0.521 true 2.271,0.979 2.396,0.75 true 2.823,0.99 2.615,0.75 true 1.854,3.24 2.292,2.823 false 1.573,0.073 1.885,0.271 0.313,0.198 10 false *a 0.083,0.927 0.396,1.125 0.313,0.198 10 false *b 0.375,1.479 0.688,1.677 0.313,0.198 10 false *c 1.979,4.302 2.292,4.5 0.313,0.198 10 false *d 2.073,1 2.427,1.24 0.354,0.24 10 false SO+ 2.813,1 3.167,1.24 0.354,0.24 10 false SO- 2.385,0.156 2.844,0.354 0.458,0.198 10 false A52 2.365,2.719 2.677,2.917 0.313,0.198 10 false *e
*a Component without harness connected
(Thermistor Assembly)
*b Sensing Portion
*c Resistance (kΩ)
*d Temperature (°C (°F))
*e Allowable Range


Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A52)Location & Routing

Click Connector(A52)Engine Compartment>Engine Room Main Wire>Ambient Temperature Sensor (Thermistor Assembly)

A52-1 (SO-) - A52-2 (SO+) 10°C (50°F) 3.00 to 3.73 kΩ
A52-1 (SO-) - A52-2 (SO+) 15°C (59°F) 2.45 to 2.88 kΩ
A52-1 (SO-) - A52-2 (SO+) 20°C (68°F) 1.95 to 2.30 kΩ
A52-1 (SO-) - A52-2 (SO+) 25°C (77°F) 1.60 to 1.80 kΩ
A52-1 (SO-) - A52-2 (SO+) 30°C (86°F) 1.28 to 1.47 kΩ
A52-1 (SO-) - A52-2 (SO+) 35°C (95°F) 1.00 to 1.22 kΩ
A52-1 (SO-) - A52-2 (SO+) 40°C (104°F) 0.80 to 1.00 kΩ
A52-1 (SO-) - A52-2 (SO+) 45°C (113°F) 0.65 to 0.85 kΩ
A52-1 (SO-) - A52-2 (SO+) 50°C (122°F) 0.50 to 0.70 kΩ
A52-1 (SO-) - A52-2 (SO+) 55°C (131°F) 0.44 to 0.60 kΩ
A52-1 (SO-) - A52-2 (SO+) 60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.

·

When measuring, the sensor temperature must be the same as the ambient temperature.

·

Use a thermometer to detect the ambient temperature of the installation area around the thermistor assembly.



HINT:

As the temperature increases, the resistance decreases (see the graph).


If the specified condition is not met, replace the thermistor assembly.