Home › Vehicle Interior › LIGHTING (INT) › BACK DOOR COURTESY SWITCH
RM3700E _58 Vehicle Interior _093025 LIGHTING (INT) _0438515 BACK DOOR COURTESY SWITCH G

LIGHTING (INT)  BACK DOOR COURTESY SWITCH  INSPECTION  


PROCEDURE

Hide 69350P 1.INSPECT BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH (w/o Power Back Door)

a.

Check the resistance.

i.
B405511C07
1.708,3.385 2.104,3.615 0.396,0.229 1.896,4.073 1.896,4.365 true 1.458,4.333 1.708,4.063 true 1.125,3.51 1.438,3.708 0.313,0.198 10 false *c 0.583,0.135 0.896,0.333 0.313,0.198 10 false *a 0.625,1.948 0.938,2.146 0.313,0.198 10 false *b 1.76,4.438 2.375,4.635 0.615,0.198 10 false ACT- 1.365,4.375 1.771,4.552 0.406,0.177 10 false D+ 1.813,3.406 2.125,3.604 0.313,0.198 10 false Y7
*a Lock
*b Unlock
*c Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y7)Location & Routing

Click Connector(Y7)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y7-2 (ACT-) - Y7-3 (D+) Unlocked Below 1 Ω
Y7-2 (ACT-) - Y7-3 (D+) Locked 10 kΩ or higher



ii.

If the result is not as specified, replace the back door lock assembly with courtesy light switch.



b.

Check the operation of the back door courtesy switch.

i.
B405511C06
1.708,3.385 2.104,3.615 0.396,0.229 2.073,4.063 2.438,4.448 true 1.896,4.073 1.896,4.427 true 1.125,3.51 1.438,3.708 0.313,0.198 10 false *c 0.583,0.135 0.896,0.333 0.313,0.198 10 false *a 0.625,1.948 0.938,2.146 0.313,0.198 10 false *b 2.49,4.385 3.104,4.583 0.615,0.198 10 false ACT+ 1.76,4.438 2.375,4.635 0.615,0.198 10 false ACT- 1.813,3.406 2.125,3.604 0.313,0.198 10 false Y7
*a Lock
*b Unlock
*c Component without harness connected
(Back Door Lock Assembly with Courtesy Light Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y7)Location & Routing

Click Connector(Y7)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y7-2 (ACT-) - Y7-3 (D+) Lock 10 kΩ or higher
Y7-2 (ACT-) - Y7-3 (D+) Unlock Below 1 Ω



ii.

If the result is not as specified, replace the back door lock with courtesy light switch assembly.



Hide 69350P 2.INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY (w/ Power Back Door)

a.

Check the operation of the closer motor.

i.
E407984C05
1.51,2.146 1.917,2.375 0.406,0.229 0.917,2.833 1.5,2.833 true 1.917,2.833 2.5,2.833 true 0.948,0.917 1.177,1.125 0.229,0.208 10 true *b 1.688,0.917 1.917,1.125 0.229,0.208 10 true *c 0.958,2.375 1.188,2.583 0.229,0.208 10 false *a 1.771,1.917 2,2.125 0.229,0.208 10 true *b 1.01,1.917 1.24,2.125 0.229,0.208 10 true *c 0.604,2.75 0.833,2.958 0.229,0.208 10 false M+ 2.583,2.75 2.813,2.958 0.229,0.208 10 false M- 1.604,2.188 2.063,2.385 0.458,0.198 10 false Y19
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Close Operation Direction
*c Open Operation Direction


Apply auxiliary battery voltage and check the operation of the closer motor.

OK:
Tester Connection Condition Specified Condition

Click Location & Routing(Y19)Location & Routing

Click Connector(Y19)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y19-1 (M-) - Y19-2 (M+) Y19-1 (M-) → Auxiliary battery positive (+)
Y19-2 (M+) → Auxiliary battery negative (-)
Open Operation
Y19-1 (M-) - Y19-2 (M+) Y19-2 (M+) → Auxiliary battery positive (+)
Y19-1 (M-) → Auxiliary battery negative (-)
Close Operation



ii.

If the result is not as specified, replace the back door lock with courtesy light switch assembly.



b.

Check the resistance of the half latch switch.

i.
B421518C23
1.51,2.021 1.938,2.281 0.427,0.26 1.927,2.781 2.333,2.646 true 1.063,2.677 1.51,2.792 true 2,0.146 2.313,0.344 0.313,0.198 10 false *e 1.51,0.083 1.823,0.281 0.313,0.198 10 false *d 0.698,0.375 1.01,0.573 0.313,0.198 10 false *c 0.219,1.115 0.531,1.313 0.313,0.198 10 false *b 2.406,2.552 2.865,2.75 0.458,0.198 10 false CLS 0.896,2.594 1.354,2.792 0.458,0.198 10 false E 0.771,0.792 1.01,1.021 0.24,0.229 10 false *f 1.208,0.49 1.458,0.74 0.25,0.25 10 false *g 1.698,0.427 1.948,0.646 0.25,0.219 10 false *h 1.115,1.969 1.427,2.167 0.313,0.198 10 false *a 1.604,2.063 2.063,2.26 0.458,0.198 10 false Y20
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position
*f 37°26'
*g 37°23'
*h 13°43'


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y20)Location & Routing

Click Connector(Y20)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y20-3 (CLS) - Y20-1 (E) Open position Below 1 Ω
Y20-3 (CLS) - Y20-1 (E) Half-latch position 10 kΩ or higher
Y20-3 (CLS) - Y20-1 (E) Full-latch position 10 kΩ or higher
Y20-3 (CLS) - Y20-1 (E) Overstroke position 10 kΩ or higher


Tester Connection Condition Specified Condition

Click Location & Routing(Y20)Location & Routing

Click Connector(Y20)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y20-3 (CLS) - Y20-1 (E) Open position → Half-latch position Below 1 Ω → 10 kΩ or higher


ii.

If the result is not as specified, replace the back door lock with courtesy light switch assembly.



c.

Check the resistance of the full latch switch.

i.
B421518C24
1.531,2.01 1.948,2.25 0.417,0.24 1.125,3.115 1.51,2.948 true 1.073,2.552 1.531,2.781 true 1.969,0.115 2.281,0.313 0.313,0.198 10 false *e 1.573,0.073 1.885,0.271 0.313,0.198 10 false *d 0.698,0.375 1.01,0.573 0.313,0.198 10 false *c 0.219,1.115 0.531,1.313 0.313,0.198 10 false *b 0.823,3.073 1.281,3.271 0.458,0.198 10 false CTY 0.927,2.469 1.385,2.667 0.458,0.198 10 false E 0.802,0.781 1.052,1.01 0.25,0.229 10 false *f 1.25,0.479 1.51,0.708 0.26,0.229 10 false *g 1.708,0.438 1.906,0.625 0.198,0.188 10 false *h 0.875,2.073 1.188,2.271 0.313,0.198 10 false *a 1.615,2.031 2.073,2.229 0.458,0.198 10 false Y20
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position
*f 37°26'
*g 37°23'
*h 13°43'


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y20)Location & Routing

Click Connector(Y20)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y20-1 (E) - Y20-4 (CTY) Open position Below 1 Ω
Y20-1 (E) - Y20-4 (CTY) Half-latch position Below 1 Ω
Y20-1 (E) - Y20-4 (CTY) Full-latch position 10 kΩ or higher
Y20-1 (E) - Y20-4 (CTY) Overstroke position 10 kΩ or higher


Tester Connection Condition Specified Condition

Click Location & Routing(Y20)Location & Routing

Click Connector(Y20)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y20-1 (E) - Y20-4 (CTY) Half-latch position → Full-latch position Below 1 Ω → 10 kΩ or higher


ii.

If the result is not as specified, replace the back door lock with courtesy light switch assembly.



d.

Check the resistance of the pawl switch.

i.
B421518C25
1.51,2.01 1.917,2.292 0.406,0.281 1.083,2.667 1.51,2.771 true 2.104,2.344 1.729,2.719 true 1.969,0.115 2.281,0.313 0.313,0.198 10 false *e 1.573,0.073 1.885,0.271 0.313,0.198 10 false *d 0.698,0.375 1.01,0.573 0.313,0.198 10 false *c 0.219,1.115 0.531,1.313 0.313,0.198 10 false *b 2.156,2.25 2.615,2.448 0.458,0.198 10 false FSW 0.948,2.594 1.406,2.792 0.458,0.198 10 false E 0.76,0.813 1.01,1.031 0.25,0.219 10 false *f 1.229,0.49 1.469,0.677 0.24,0.188 10 false *g 1.688,0.438 1.938,0.635 0.25,0.198 10 false *h 0.802,2.083 1.115,2.281 0.313,0.198 10 false *a 1.594,2.073 2.052,2.271 0.458,0.198 10 false Y20
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Open Position
*c Half-latch Position
*d Full-latch Position
*e Overstroke Position
*f 37°26'
*g 37°23'
*h 13°43'


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y20)Location & Routing

Click Connector(Y20)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y20-2 (FSW) - Y20-1 (E) Open position 10 kΩ or higher
Y20-2 (FSW) - Y20-1 (E) Half-latch position 10 kΩ or higher
Y20-2 (FSW) - Y20-1 (E) Full-latch position 10 kΩ or higher
Y20-2 (FSW) - Y20-1 (E) Overstroke position 10 kΩ or higher


Tester Connection Condition Specified Condition

Click Location & Routing(Y20)Location & Routing

Click Connector(Y20)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y20-2 (FSW) - Y20-1 (E) Open position → Half-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher
Y20-2 (FSW) - Y20-1 (E) Half-latch position → Full-latch position 10 kΩ or higher → Below 1 Ω → 10 kΩ or higher


ii.

If the result is not as specified, replace the back door lock with courtesy light switch assembly.



e.

Check the resistance of the sector switch.

i.
E407986C05
1.469,2.042 1.896,2.271 0.427,0.229 1.031,2.708 1.458,2.708 true 1.927,2.885 2.354,2.885 true 2.448,2.813 2.906,3.01 0.458,0.198 10 false OPN 0.875,2.635 1.333,2.833 0.458,0.198 10 false E 0.958,2.25 1.271,2.448 0.313,0.198 10 false *a 1.031,0.469 1.344,0.667 0.313,0.198 10 false *b 1.573,2.094 2.031,2.292 0.458,0.198 10 false Y20
*a Component without harness connected
(Back Door Lock with Courtesy Light Switch Assembly)
*b Sector Gear in Neutral Position


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y20)Location & Routing

Click Connector(Y20)Body>No. 2 Back Door Wire>Back Door Lock with Courtesy Light Switch Assembly

Y20-6 (OPN) - Y20-1 (E) Sector gear in neutral position
(Sector switch on)
Below 1 Ω
Y20-6 (OPN) - Y20-1 (E) Sector gear not in neutral position
(Sector switch off)
10 kΩ or higher



ii.

If the result is not as specified, replace the back door lock with courtesy light switch assembly.