The air conditioner pressure sensor, which is installed to the high pressure side pipe to detect refrigerant pressure, sends a refrigerant pressure signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly converts this signal to a pressure value according to the sensor characteristics and uses it to control the compressor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| P053011 | Refrigerant Pressure Sensor Circuit Short to Ground | Diagnosis Condition:
Ignition switch ON Malfunction Status: Short in air conditioner pressure sensor circuit Detection Time: Continuously for 4 seconds or more |
·
Air conditioner pressure sensor ·
Harness or connector ·
Air conditioning amplifier assembly |
Memorized | Air Conditioner | A |
Pre-procedure1
Install a manifold gauge set.
Procedure1
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Regulator Pressure Sensor | Air conditioner pressure sensor | Min.: -32.768 MPaG
Max.: 32.767 MPaG |
Actual refrigerant pressure displayed | ·
Refrigerant line (gas leak etc.) ·
Air conditioner pressure sensor circuit malfunction |
| Tester Display |
|---|
| Regulator Pressure Sensor |
Compare the values displayed in the Data List and on the manifold gauge set.
| Result | Proceed to |
|---|---|
| The values displayed in the Data List and on the manifold gauge set does not match | A |
| The values displayed in the Data List and on the manifold gauge set match | B |
Post-procedure1
None
A
B
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>ON-VEHICLE INSPECTION
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Regulator Pressure Sensor | Air conditioner pressure sensor | Min.: -32.768 MPaG
Max.: 32.767 MPaG |
Actual refrigerant pressure displayed | ·
Refrigerant line (gas leak etc.) ·
Air conditioner pressure sensor circuit malfunction |
| Tester Display |
|---|
| Regulator Pressure Sensor |
Disconnecting the A51 connector of the air conditioner pressure sensor causes the Data List value to change.
| Result | Proceed to |
|---|---|
| Regulator pressure sensor value changes | A |
| Regulator pressure sensor value does not change | B |
A
B
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51)Location & Routingewd_type=routing;type=c;code=A51 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=3 |
||
| A51-3 (+) - Body ground | Ignition switch ON | 4.75 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the H23 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51,H23)Location & Routingewd_type=routing;type=c,c;code=A51,H23 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=3 Click Connector(H23)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=H23;pinno=11 |
||
| A51-3 (+) - H23-11 (S5-3) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51)Location & Routingewd_type=routing;type=c;code=A51 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=2 |
||
| A51-2 (PR) - Body ground | Ignition switch ON | 3.0 to 5.25 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the H23 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A51,H23)Location & Routingewd_type=routing;type=c,c;code=A51,H23 Click Connector(A51)Engine Compartment>Engine Room Main Wire>Air Conditioning Pressure Sensorewd_type=component;type=c;code=A51;pinno=2 Click Connector(H23)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=H23;pinno=36 |
||
| A51-2 (PR) or H23-36 (PRE) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG