The air conditioning control assembly communicates with the air conditioning amplifier assembly via LIN communication.
If a malfunction occurs in the LIN communication system, the air conditioning amplifier assembly will not operate, even if the air conditioning control assembly is operated.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|
| B14B287 | Lost Communication with Front Panel LIN Missing Message | Diagnosis Condition:
Ignition switch ON Malfunction Status: Error or lost communication with air conditioning control assembly Detection Time: Continuously for 10 seconds or more |
·
Air conditioning control assembly ·
Harness or connector ·
Air conditioning amplifier assembly |
Memorized | Air Conditioner | A |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction | Error communication with air conditioning control assembly | ○ | - |
| Lost communication with air conditioning control assembly | - | ○ | |
| Detection Time | Continuously for 10 seconds or more | Continuously for 10 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions of either of these patterns are detected, a DTC will be stored.
Inspect the fuses for circuits related to this system before performing the following procedure.
Pre-procedure1
Disconnect the H31 air conditioning control assembly connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H31)Location & Routingewd_type=routing;type=c;code=H31 Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assemblyewd_type=component;type=c;code=H31;pinno=9 |
||
| H31-9 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H31)Location & Routingewd_type=routing;type=c;code=H31 Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assemblyewd_type=component;type=c;code=H31;pinno=13 |
||
| H31-13 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the H24 air conditioning amplifier assembly connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H31,H24)Location & Routingewd_type=routing;type=c,c;code=H31,H24 Click Connector(H31)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Control Assemblyewd_type=component;type=c;code=H31;pinno=7 Click Connector(H24)Instrument Panel>Instrument Panel Wire / Speaker Wire>Air Conditioning Amplifier Assemblyewd_type=component;type=c;code=H24;pinno=7 |
||
| H31-7 (LIN1) - H24-7 (LIN1) | Always | Below 1 Ω |
| H31-7 (LIN1) or H24-7 (LIN1) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect the H24 air conditioning amplifier assembly connector.
Procedure1
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Terminal No. | H24-7 (LIN1) - Body ground |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Connect the air conditioning control assembly connector.
Procedure1
| *a | Component with harness connected
(Air Conditioning Control Assembly) |
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Terminal No. | H31-7 (LIN1) - Body ground |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Ignition switch ON |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG