Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0440204 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the stop light switch assembly connector.


Procedure1

a.
E409581C42
1.479,0.083 1.885,0.323 0.406,0.24 1.302,1.333 1.135,1.885 true 2.292,1.333 2.781,1.594 true 2.063,1.333 1.906,1.875 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.563,0.115 1.99,0.333 0.427,0.219 10 false A63 2.844,1.542 3.01,1.708 0.167,0.167 10 false B 0.958,1.917 1.375,2.104 0.417,0.188 10 false GND 1.844,1.906 2.01,2.073 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-7 (B) - A63-2 (GND) Always 11 to 14 V
A63-6 (B) - A63-2 (GND) Ignition switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63-2 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.


Post-procedure1

a.

Reconnect the stop light switch assembly connector.


Procedure2

a.
E409580C15
1.51,0.083 1.927,0.385 0.417,0.302 2.313,1.24 2.896,0.938 true 2.135,1.26 2.49,1.875 true 1.927,1.271 2.281,1.885 true 1.24,1.865 1.698,1.292 true 0.865,1.948 1.49,1.281 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.594,0.135 2.052,0.333 0.458,0.198 10 false A63 2.969,0.833 3.313,1.073 0.344,0.24 10 false OUT 2.552,1.823 2.896,2.063 0.344,0.24 10 false GND 2.281,1.906 2.438,2.104 0.156,0.198 10 false L 1.063,1.896 1.406,2.135 0.344,0.24 10 false ACC 0.76,1.917 0.917,2.115 0.156,0.198 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A63)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

A63- 1 (OUT) - A63-2 (GND) Brake pedal released 1.5 V or less
A63-1 (OUT) - A63-2 (GND) Brake pedal depressed 11 to 14 V
A63-3 (L) - A63-2 (GND) Brake pedal released 1.5 V or less
A63-3 (L) - A63-2 (GND) Brake pedal depressed 11 to 14 V
A63-4 (ACC) - A63-2 (GND) Always 11 to 14 V
A63-5 (L) - A63-2 (GND) Ignition switch on (IG), brake pedal released 7.5 to 14 V
A63-5 (L) - A63-2 (GND) Ignition switch on (IG), brake pedal depressed 0 to 1.5 V


If the result is not as specified, replace the stop light switch assembly.