Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC LIGHT CONTROL SENSOR
RM3700E _59 Vehicle Exterior _093283 LIGHTING (EXT) _0440205 AUTOMATIC LIGHT CONTROL SENSOR G

LIGHTING (EXT)  AUTOMATIC LIGHT CONTROL SENSOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89120A 1.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

Pre-procedure1

a.

Disconnect the H78 automatic light control sensor connector.


Procedure1

a.
E393536C10
1.51,0.25 1.917,0.51 0.406,0.26 0.906,1.688 1.406,1.188 true 1.635,1.698 1.615,1.208 true 0.354,0.26 0.667,0.417 0.313,0.156 10 false *a 1.583,0.292 2.042,0.49 0.458,0.198 11 false H78 1.479,1.719 2.094,1.917 0.615,0.198 10 false CLTE 0.708,1.719 1.323,1.917 0.615,0.198 10 false CLTB
*a Front view of wire harness connector
(to Automatic Light Control Sensor)


Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H78)Location & Routing

Click Connector(H78)Instrument Panel>Instrument Panel Wire / Speaker Wire>Automatic Light Control Sensor

H78-1 (CLTB) - H78-2 (CLTE) Ignition switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H78)Location & Routing

Click Connector(H78)Instrument Panel>Instrument Panel Wire / Speaker Wire>Automatic Light Control Sensor

H78-2 (CLTE) - Body ground Always Below 1 Ω


If the result is not as specified, there may be a malfunction on the wire harness side.


Post-procedure1

a.

Connect the H78 automatic light control sensor connector.


Procedure2

a.

Connect an oscilloscope to terminals H78-2 (CLTE) and H78-4 (CLTS) of the automatic light control sensor connector and check the waveform.

E393537C06
1.719,0.771 2.167,1 0.448,0.229 1.156,2.094 1.656,1.677 true 2.323,2.083 1.99,1.667 true 0.521,0.677 0.833,0.833 0.313,0.156 10 false *a 3.5,0.677 3.813,0.833 0.313,0.156 10 false *b 1.813,0.802 2.271,1 0.458,0.198 10 false H78 6.375,2.083 6.833,2.281 0.458,0.198 10 false GND 0.958,2.115 1.406,2.313 0.448,0.198 10 false CLTS 2.208,2.115 2.656,2.313 0.448,0.198 10 false CLTE
*a Component with harness connected
(Automatic Light Control Sensor)
*b Waveform


OK:
Tester Connection Condition Tool Setting Specified Condition

Click Location & Routing(H78)Location & Routing

Click Connector(H78)Instrument Panel>Instrument Panel Wire / Speaker Wire>Automatic Light Control Sensor

H78-2 (CLTE) - H78-4 (CLTS) Ignition switch on (IG) 2 V/DIV., 10 ms./DIV. Pulse generation
(See waveform)


HINT:

The communication waveform changes according to the surrounding brightness.


If the result is not as specified, the automatic light control sensor may be malfunctioning.