This DTC indicates that the hybrid vehicle control ECU detected an instantaneous interruption in +B power source voltage.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P06881F | ECM/PCM Power Relay Sense Circuit Intermittent | When the ignition switch is ON (READY), the hybrid vehicle control ECU is reset due to an instantaneous interruption of power source.
(1 trip detection logic) |
·
Wire harness or connector ·
Hybrid vehicle control ECU |
Comes on | Master Warning: Comes on | Hybrid Control | A |
After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY) and wait for 30 seconds or more.
(If the DTC is not output, drive the vehicle on urban roads according to the freeze frame data item "Vehicle Speed" for approximately 5 minutes.)
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Confirm whether the auxiliary battery terminals have been disconnected recently.
| Result | Proceed to |
|---|---|
| Terminals have been disconnected. | A |
| Terminals have not been disconnected. | B |
A
B
Pre-procedure1
Turn the ignition switch to ON (READY) from off.
Procedure1
Confirm that the master warning illuminates.
| Result | Proceed to |
|---|---|
| Master warning illuminates | A |
| Master warning does not illuminate | B |
DTC P06881F may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the ignition switch is turned off and then ON (READY) again. In this case, clear the DTCs to complete the inspection.
Post-procedure1
Turn the ignition switch off.
A
B
Read and record the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for 2 minutes or more.
NEXT
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P06881F and other DTCs are output | A |
| Only P06881F is output | B |
| None of the above conditions are met | C |
Post-procedure1
Turn the ignition switch off.
A
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Check the connection of the auxiliary battery terminal.
The terminal is connected securely and there is no contact problem.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the IGCT relay from the No. 5 relay block assembly.
Disconnect the H44 hybrid vehicle control ECU connectors.
Procedure1
Measure the resistance according to the value(s) in the table below.
| *1 | No. 5 Relay Block Assembly | *2 | IGCT Relay Holder |
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H44)Location & Routingewd_type=routing;type=c;code=H44 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=7,8 |
||
| H44-7 (+B1) - 5 (IGCT relay holder) | Ignition switch off | Below 1 Ω |
| H44-8 (+B2) - 5 (IGCT relay holder) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the H44 hybrid vehicle control ECU connectors.
Reinstall the IGCT relay.
OK
NG
Check for intermittent problems.
Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 5 relay block assembly.
When the ignition switch is ON (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 5 relay block assembly.
| Result | Proceed to |
|---|---|
| Problem symptom does not recur | A |
| Problem symptom recurs | B |
A
B